void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
With reference to the following known issue: NCSIDB-114: Default logging causes for nrf connect sdk 1.3.2. Is there any further documentation regarding the workaround mentioned...
Hi,
I have installed Segger Studio for ARM v6.22a.
I have also installed the SDK5 version 12.3.0.
I imported the IAR project project ble_app_start_notification_pca10028_s130...
Hi,
The datasheet of nRF52810 says that, if the voltage drops below the operating voltage, the device shall undergo a brownout reset itself and it is supposed to work normally...
Hello nordic, I'm developing a sensor that will be used sometimes in environments without LTE signal. When the sensor starts up, I'd like to check connectivity, and if there...
Hello I'm using segger,i had my own project which its name is example_detector distance , i m trying to build this project by using make -j10 . all the files were compiled...
Hello !
I was trying to communicate with my Acsip chip, when I saw that the problem was coming from the nrf_serial_read() function. And here is my setup :
- I use the...
Hello, I want to understand why some example with the "nrf52832" crash. My project is about to scan BLE device to found tags.
To start, I have tried multiples examples from...
Hi,
As far as I understand it, TF-M stores symmetric keys unencrypted on flash in the nrf91, and then uses other means (like flash read protection and trustzone) to keep...
(replica as the previous post was archived by accident...)
Hi,
I'm trying to incorporate LittleFS into our development. We are relying on services provided by TF-M....
Hello,
first of all i am a new user of NRF microcontrolers and embedded systems. I ve been searching on this forum for a simple PDM microphone example and although there...
I want to Enable and Disable Application and network core at some point in the mid of the code. What configuration would i be required to switch the cores or Enable/Disable...
hello,
i am using nrf52832 with sdk 15.2 i want to store signed int values in to nvs (like rssi and tx power) so that i can change these in run time
i can able to...
We are trying to achieve automatic scan and join in both LTE-M and NB-IoT network modes. We are using SICA B1 -SiP with modem FW 1.3.1, and %XSYSTEMMODE=1,1,0,0 setting. ...
I am developing a product that I have going into SYSTEM_SOFT_OFF to maximise battery life. I have a bunch of GPIOs (these are currently just buttons on the nRF52-DK) that...
