VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
I'm currently working with a BL5340PA module with the external antenna connector. we were wondering what was the RF switch isolation between the two antenna outputs. In other...
Hello,
I am currently working on a project using a custom board with nRF52840 + nRF21540 . I am trying to measure wireless performance using Direct Test Mode (DTM) , but...
Hi, when I use OTBR to commission a matter bulb(52840DK), I found this log:
I: 7371 [DL]CHIPoBLE connection established (ConnId: 0x00, GATT MTU: 247) D: 7448 [DL]Indication...
Hi,
I have been trying to use the radio_test example application to try and accomplish my goal but no success so far. My goal is to be able to compose an advertisement packet...
Hello, we would like to use the 4th reference circuit with the QIAA footprint from the Nordic nRF52840 chip's datasheet. However, in our PCB design, can we change the placement...
Hello,
I'm attempting to write to a ble characteristic but when i call bt_gatt_write, I get BT_ATT_ERR_INVALID_ATTRIBUTE_LEN, I have tried to send the same command using...
Question: I am working with the Ebyte E73-2G4M08S1C module, which is based on the nRF52840 . The module provides D+ and D- lines . Can these lines be used for debugging and...
Hello,
I'm trying to put the nRF54L15DK into System Off mode, using sdk & toolchain version v2.8.0.
The provided example (\samples\nfc\system_off) works on my evaluation...
Hello Team, We are currently building a circuit using nRF52833 QDAA QFN40 ( Configuration 5). We would like to know if there are dedicated pins to be configured for BOOT as...
Hi everyone,
I'm working on a Matter based project on the NRF52840 SoC. Since it's an Iot project project we need to reduce power consumption at it's minium for lifetime...
We're starting new medical research project where we have to send data at rate of around 4Mbps from the sensor array for a distance (omnidirectional) of around 2 meters. The...
Good day,
I am learning how to program NRF52832 chips using the NRF52 DK. I am using Segger embeddded v8.2 for the moment as I have not yet learnt how to use the NRF Connect...
Hi,
We have a project based on NRF52811_xxAA_REV1 running on multiple devices without any problem.
Nordic announced recently newer version of SoC (REV2, aka B0) and since...
