Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hi Nordic,
I am trying to build something based on your BLE uart example for the two units for the connection from your SDK 17.0.2
one unit is running the BLE UART central...
Dear nordic,
I need a advise from your side. my custom board has two spi device both are working same line. one is SD card interface and other is sensor which works in DMA...
nrf9160-DK to NB-IOT service at vodafore UK
```
[00:00:00.322,479] [0m<inf> asset_tracker: Connecting to LTE network. [0m[00:00:00.329,193] [0m<inf> asset_tracker: This...
I know that we have actually some countries in Europe which don't support LTE-M, therefore we like to have a fallback.
Does there exist a fallback option to GSM or EGPRS...
Hi,
So I was having an error which caused my application to stall in the "do_stop_check" part of the nrf_drv_twi.c file, so I added a bit of code to check if I could figure...
We have a device with the following configuration:
nrf5_SDK_for_Mesh_v3.1.0
nRF5_SDK_15.2.0
s140_nrf52_6.1.0_softdevice
mesh_bootloader_gccarmemb_nrf52840_xxAA ...
Hi,
I'm trying to make a script in Python using the nRF52840 dongle, to make some BLE advertising.
I'm using:
- Python 3.7.2 (32 bit)
- pc_ble_driver_py library
...
Hi everyone,
I'm using ses IDE to debug via J-link on nRF52840 DK.
I'm debbuging CDC ACM example ( I haven't changed it ) but when I debug: ret = app_usbd_cdc_acm_write...
I am designing a PCB for the nRF52833 aQFN chip. To reduce the cost of the PCB I would like to fanout the inner row of the IC package on a single layer by using 3/3mil traces...
Hello,
I have a certificate attached, but in my personal account it gives an error when I enter the DK data.
Please tell me why the error occurs?
OS: macOS 10.13.6 ...
Hi,
I am using IM69D130 MEMS sensor with nrf52832 I just want to confirm the output of pdm sensor . please any one suggest how should i proceed . how do i code for it ?...
I am attempting to migrate my BLE project to a higher security level with bonding. Was mode 1 level 2 and am upgrading to mode 1 level 4. When I change the configuration to...
