Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
I want to know how to control BLE connection of nRF52832. I am using softdevice S132. I have a device that works centrally and a device that runs peripherals. When the peripheral...
nrf52832.
SDK14.2
Segger ES V3.34a
Options for Sequential Serial numbers
We have managed to program a single serial number into the UICR, using our Development...
I am trying to interface I2C EEPROM (AT24C512) with nrf52840 and I am directly writing to and reading from the registers mentioned in the datasheet. I am seeing the i2c waveforms...
Hello -
We are also bumping into the problem described here , where it is not possible to initialize LESC when BLE is initialized from a FreeRTOS task. The nrf_stack_info_overflowed...
nRF52DK
external board with 51822 and mems
I connect my external board with nRF52DK as this (left is board, right is nRF52DK):
SWCLK -> SWDCLK
SWDIO -> SWDIO
VCC...
Hi,
I got some troubles on the communication distance between the two units which one acts as central and one acts as peripheral, I tried to adjust the BLE parameters the...
Dear Sir,
I have enabled my project for SPIM+EasyDMA.
I am configuring the SPIM transfer nrf_drv_spi_xfer with additional flags like,
NRF_DRV_SPI_FLAG_NO_XFER_EVT_HANDLER...
nRF51822 QFAA
At first I set up the RAM size to 0x1F80, it works fine. However, after I try to use RTT to print log, I got the compile error: region RAM overflowed with...
Hi ... how to set the password to secure the connection between the device and application . I don't want to anyone to connect my device , for that i am planning to the set...
I have a nRF52 DK. I'd like to debug my board which has nRF51822 and sensors, and has SWCLK, SWDIO, VCC, GND, RX, TX, VCC, GND. Please provide detail steps on how to wire...
I'm developing a central that discovers services in a peripheral. The services are both custom and standard BLE services. Discovery is working fine, but there is one issue...
Hello,
We are experiencing a rare condition whereby we read in raw Accelerometry data (758 bytes) over the SPI bus, and sometimes (rarely), we'll get a block of repeated...
Hello Everyone, I designed and fabricated a small nRF52 board. The design of this board is based on the Adafruit nRF52 feather. The difference between my designed board and...
Hi,
I'm working on MacOS 10.14.6 and I'm having trouble with the Programmer app in nrf Connect.
I have installed the Jlink driver successfully (v6.60a), but when I select...
