I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
Hi,
I have nRF9160 DK. I want to update firmware to (From Your WebSite: Link Pasted)
nRF9160 LTE-M/NB-IoT/GPS Modem firmware
https://www.nordicsemi.com/Products/Low...
Since nrfConnect Programmer, ninja flash/west flash ALL use nrfjprog behind the scenes, I wish I could find out _exactly_ which nrfjprog commands the nrfConnect Programmer...
Hi,
I'm trying to reduce the current consumption. I can't use sd_power_system_off because I don't want my device to rest when it wakes up. So the other way to do this is...
Can i commuicate over USB CDC on holyiot nrf52480 by giving Vbus(5v) , D+,D- , gnd from pc. and get output on VDD or do i have to also supply voltage on VDD(3V) ? I wanted...
Using nrfx_timer_extended_compare I would like to periodically adjust the compare value of a running timer. It seems to work without disabling the timer before this and re...
Hi，
Dear， I have a question about Fstorge and Bootloader. If my app layer calls the Fstorge API to store some data, will the data saved by the Fstorage API be erased when...
Hello All,
I am running into a mesh assert error when running the light switch server demo on a custom board w/ the NRF52840 (MDBT50-1M). The device starts up fine, has...
Hi all
I am studying mesh example such as light switch server, I use Segger Embedded Studio to comple the project of light switch, it is OK, but when I want to do online...
Hi,
I'm developing a BLE DFU controller with bluepy on a RPi3. The peripheral that is being updated is a nRF51 device on SDK 12.3.0, with the secure bootloader and experimental...
Hi,
In our project we want to use nRF52832 chip using HCI Command interface. We are trying to use Zephyr RTOS project for geting HCI interface through UART. We are using...
Hi,
In y project, I want to implement CTS. Until now it's been working, but I don't know why, I now have this problem: Current Time Service not found on server, which means...
I am using a Sparkfun Pro nRF52840. I wish to communicate with it serially. I found the UUIDS it exposed : UART Service = 6E400001-B5A3-F393-E0A9-E50E24DCCA9E TX Characteristic...
Hi,
I am using nrf51 dk with sdk 12.3 and softdevice S130 bluetooth module using Keil IDE.In our project we need to send sensor data from the nrf51 bluetooth module to another...
