I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
Hello
I am using Android and BLE communication with nRF52832 (BLENano2) now.
I am using SDK 15.0.0 with keil uversion.
Central is Android and peripheral is nRF52832...
Hi,
we have a custom board running the nrf52840. The code is getting pretty good we are getting close to beta. We are using SES as our development platform and are currently...
Hi
I'm using pc-ble-driver-py(python2.7).
I read that python2.7 will not be maintained past 2020.
So, i want know about pc-ble-driver-py update plan.
When will the...
Hello,
We have an application based on NRF52832 which runs Nordic UART service and DFU service SDK15.2 SD132V6.0. Now, we need to add “high speed data pipe” and we are...
Hi,
I have been using nRF24 in many projects with Arduino. So far quite good experience.
Now I transfer to STM32 and have a strange problem, I cannot send with STM32 as...
Hi,
Has anyone tried connecting the grove_display to the nRF9160?
http://wiki.seeedstudio.com/Grove-LCD_RGB_Backlight/
I have tried the code below
https://github.com...
Hi All,
I'm trying to understand certificate goes where from AWS-IOT to certificate.h.
when setting a new device, I have these 4 certificates:
also the ROOT CA contains...
I have a custom Characteristic in my GATT that is sending data in Notify mode every 30ms.
In my firmware I use timer to do this with something like this :
Everything...
I'm looking to test the DPPI peripheral on the dev-kit, and to that end I though a good example would be to setup the DPPI peripheral to trigger an event when a button is...
Hi, I am new in the development. I want to interface the relay withe ble module.
But not able to do that. Please any one help me to interface the relay. Thanks in advan...
Hi,
Asset tracking example used to work for me, after reinstalling my environment I get nrf_cloud_connect failed: -111
this is the output from the LTE link monitor:
...
Hello,
I'm using the same SDK used on the Thingy:52, compiling with GCC. I'm using the Rigado BMD-350-A which uses the nrf52832.
I'd like to use P0.09 and P0.10 as GPIO...
I have three buttons connected to pins PO.07, PO.08, PO.09 on my card. I changed the pin assignment and for the first two I have no problem using them as buttons, but I can...
