Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I need to port a system from a STM32F407 MCU to the nrf52832.
The old system would continuously poll a SPI slave for 244 bytes of information and after receiving 60 valid...
Hi,
I am working on the ADC and trying to sense the battery level to measure it voltage.
And I have configure the ADC with normal conditions as present in example of SDK...
Hello
First things first, when I use the UART example located in:
\nRF5_SDK_15.2.0_9412b96\examples\peripheral\uart\pca10040\blank\ses
all works fine, the script compiles...
Hi,
I hope this is the correct place to ask beginner questions. I new to microcontrollers in general.
So first of all here is what I am using currently:
Software:
...
Hi,
I'm using Nrf52 with SDX 15.2.
The device is far for the host (smartphone), I would like to know if I can know the RSSI with the Smartphone? How can I control the...
Hello everyone!
I'm trying to implement a mqttsn client inside a microcontroller, and the nrf52840 should be used only as a way to communicate with other thread devices...
Hello!
My name is Tiago Morais. I've started to work with nrf52840 and now I'm having some problems with its CLI.
I'm trying to use the nrf52840 dk with openthread and...
Dear Nordic Team, Thanks for supporting.
Currently i am working with DFU for nRF52810 custom board. I am using SDK15.2.0. I followed these steps (//devzone.nordicsemi.com...
Hi all,
I'm following https://www.nordicsemi.com/DocLib/Content/SDK_Doc/Mesh_SDK/v3-0-0/md_doc_getting_started_dfu_quick_start and I'm using mesh SDK v3.0.0, I have a problem...
Hi all:
All of the example code is using GPIOTE to demonstrate how to handle GPIO interrupt.
However, it just can configured HiTOLow/LowToHi/Toggle.
If I want to trigger...
Works
Use nRF Connect v2.6.0 on Linux to erase, program softdevice.
Works
Use Keil to program application firmware
Does not work:
Use nRF Go studio to detect...
I need to implement a simple uart protocol. most messages are fixed length (8bytes) with some exceptions.
here what I do in pseudo code, I send 8bytes and expect 8bytes...
Hi
I am trying to port an SPI driver from a project for the NRF51822 to an NRF52832 and running into a problem reading more than two bytes. We are using SPI0 (not SPIM0...
Hello,
I'm using an NRF52 DK board.
I noticed that when I change P0.27 from the default (input / not connected to input buffer) to being an input pin connected to the...
Good evening,
I had a question in respect to the exact procedure needed to read a characteristic with read permissions. I have just discovered a service i would like to...
