void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi,
I have been trying to modify the LVGL example to work with an 480x320 SPI TFT screen (adafruit's 480x360 TFT featherwing specifically). I have gotten working with 240...
Hi,
I cannot bond to NRF5340DK running the `peripheral_ancs_client` sample if external oscillator configuration is disabled (thus using synthesized from HFCLK).
Environment...
Hi,
Iam trying to implement multirole ble in nrf5340 using ncs. I am using legacy advertizing type for advertize and observing both.
why it is working only first time...
Hi nRF support team,
In my application, I need to show system date and time, so I am trying to get the system epoch time by using the nRF Connect SDK on nRF52840 dev kit...
Since I am a beginner with Zigbee, I would appreciate your guidance.
Currently, I am using the nRF Connect SDK v2.8.0(Zigbee-addon) with the nRF54L15 to work with Zigbee...
Hi there. I'm attempting to do trilateration between 3 nRF Devices. A1, A2, and A3.
A1 - A2 I can get using the nRF Distance Measurement toolbox
A1 - A3 I can get using...
We have implemented a simple contact switch using the nrf52840 and the latest zip generator (v99). The device connects to a Samsung Smart things edge router. A contact device...
Hello Nordic Team,
HW: nRF52840DK
SDK: ncs v2.8.0
App: hci_pwr_ctrl
I am testing with hci_pwr_ctrl example to see how tx power can be set from application.
The...
I am working my way through the Beginner course on Dev Academy, and am trying my hand at using my own accelerometer breakout board communicating over I2C for lesson 6.
I...
Hi,
I have used course's example for GPIO interrupt for toggling LED and used to update BLE adv parameters without using DK buttons library. But, as soon as, I update BLE...
Hi there, I'm new to the nrf/zephyr sdk and while using the nRF5340dk board, I've found that the pin1.01 is pulled high right after the board powers up. My assumption is that...
Hi All
Hi, I am using nrf51822 controller in my design for with SMD chip antenna for RF output.
Can anyone suggest me any reference design(Hardware and Layout files) to...
I'm attempting to initialise my first zephyr project using the nRF SDK, and have been following the academy course on the nRF boards. Problems arise on the install SDK (2...
Hi,
Only the TX and RX of NRF52840 chip UART are used to test OpenThread CLI Demo. How can I change the configuration of UART in the original CLI Demo?
Thanks.
Hi,
"In a BLE Mesh network, if a client uses GAP attributes to send data, can it also use the GATT profile to communicate with a single device? For example, can the client...
