Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
Hello Nordic team,
I've recently upgraded my application from nRF Connect SDK v2.7.0 to v2.8.0 , and the previous BLE Disconnect issue has been resolved — thanks again for...
Hi, I want to set different gap event length for different peripheral on a ble central: 1 link with high throughput and 4 links with low throughput.
The sdk is 17.0.2...
Greetings!
Briefly summarized: I am trying to generate SPDX files for our project, but I hit some roadblocks while running the west spdx command. I found a way to workaround...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi !
I have a peripheral that can connect to other nRF52's or a smart phone such as iPhone or android. Is there an easy way to detect a smart phone?
The best I can think...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm using \nRF5_SDK_15.3.0_xxxxx\examples\peripheral\usbd_ble_uart example to use two communication links. Missing echo on the USB virtual COM is a small frustration. I've...
Hi NordicSemi
I have a project where we receive data via the UARTE. To avoid missing data caused by higher prioritized tasks we want to use the DMA facilities.
nrf52832...
Hi,
i want to flash programs with the Segger Embedded Studio to my Thingy 91. I already am able to flash hex files with the nRF Programmer to the thingy 91. I installed...
In addition to (obviously!) a 52811 chip and a BLE beacon, what additional hardware would one need for reasonably accurate location tracking of a BLE tag/beacon? I'm generally...
Hello Devs,
I have enabled NRF_LOG in my project, but I would like to disable it in, for example, the main.c file, but keep it working in others files.
at the moment...
Hi all, I am stuck with a simple but weird issue. It's driving me crazy for the last few hours. I am using a PCA10056 DK. I am somehow unable to do a simple digital pin read...
hi ...
I am working on mesh 3.1 version . I have used light switch example . In this case , i am sending the character in generic_onoff_set_cb , and changed from bool to...
I am trying to pair the BleHeartReteMonitor example in pc-ble-driver. I have gotten to the point where I get the pairing request from the central and I get its capabilities...
Hello, Nordic!
I'm developing with nrf52840, s340, sdk 15.3.0
I made my app_error_fault_handler. It is very good for me.
I sometimes got an error. So I saw that log...
Hi guys I m trying to send a simple message every time a gpio interrupt occurs on the client in order to receive that on the server. I m using the ble mesh protocol and I...
Hi
We will use the 52811 together with nRF9160 for short range communications. Currentconsumptionwise which interface is recommended, UARTR, TWI or SPI?
I am trying to run the example secure_bootloader\pca10040_ble_debug. The application does crash during a debug print with following stack trace:
Any idea what could...
I've reached a critical point in the firmware development process where I need to start considering integrating a bootloader with the application code.
I have a custom board...
Hi,
I'm trying to update the modem firmware on my nRF9160. I believe the current firmware is mfw-m1_nrf9160_0.6.8-30.alpha. I followed Martin's suggestions here , but nRF...
Hi,
If i had a purpose of including Ble files into peripheral example then what is the way i can approach?Is it by including all neccessary header file paths,adding sources...
