Hello!
We are planning to purchase an electronic component nrf52840 and produce a finished product on it.
question
1. Will it work immediately on the ZIGBEE 3.0...
Good morning, I have a question about NRF Util. I need to make some changes in souce code of nrfutil for my own needs, but the most recent version, which is provided on Github...
Hi. I interested now for direction finding in nrf52 series. I have nrf52811, nrf52833 and other controllers. But i don't find any information how develop board for recievers...
Zephyr Eddystone example is connectable after power on of nrf52833 board. But after disconnect it becomes non connectable. How to fix it? And how to change advertisement interval...
We are looking for an experienced software developer, for existing board with using nRF Connect SDK. We are using nRF52840-dk.
Please, contact me if you are interested.
Hi,
I would like to disable TWIM peripheral when not needed to save some power and enable it just before it's needed. Is there any delay after writing to NRF_TWIMx->ENABLE...
I want to get vdd without timer
so i found this.
https://devzone.nordicsemi.com/f/nordic-q-a/38239/nrf-52832-saadc-without-timer/147517#147517
and change some part like...
I have a design, using the NRF24L01+, that I would like to run from batteries. The Transmitting device is not a problem, because it can turn off when not transmitting.
For...
Hi All,
For NRF52 is that possible to configure the system to use a different pin for RESET than GPIO 21? We want to reset the NRF on errors, if our other MCU detects some...
Board：PCA10056 （0.9.3）
SDK：15.2
Softdevice：S140
Example：ble_app_blinky
Today，I follow this page Using an ampere-meter for current measurement to measure the current...
Used SDK: 15.2.0
Hello,
I want to print some debug messages over RTT after an error occured. After that I want to reset the system.
If I put the string into the que...
I've followed the steps to set up the SDK.
When I execute the batch file(setup_sdk.bat), there is something wrong occur (as below pic)
I've installed the git and add...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi there,
I am trying to use UART on the nRF52840 on a custom PCB. The custom board is connected to the nRF52840-DK with a debug connector. Am I free to set any pins on...
I want to create a router that only communicates with Bluetooth, not the gateway that connects to other networks.
The configuration is as follows.
C oordinator + Router...
Greetings,
I'm having troubles getting the Mesh lighting demo to work. Here are the details:
IDE = SES 4.12
SDK = nRF5 SDK v15.2.0, nRF5 Mesh SDK v3.1.0
SoftDevice...
Hi, Is there a usb hidapi sample code for nrf52840 somewhere? I know that there is a sample code of usbd_cdc_acm. Using the HIDAPI library link below , It will be beneficial...
Hi,
I am working on a Bluetooth Mesh project in which I am trying to add support for NFC, but I get the following error " error: multiple definition of `SWI2_EGU2_IRQHandler...
I'm new to nRF9160. I have some experience of implementing stm32 MCU and HL8548(3G module).
I want to send at commands to outside module like Wifi module, and receive return...
I have Nordic NRF 52840 DK development board, using Ubuntu 18.04, I loaded "ble_connectivity_s140_usb_hci_pca10056" to the board successfully. Then I powered cycle and cannot...
