How do I map the build codes noted in the Rev Errata to the stamps on our ICs? I have two versions with QFAAAB and QFAABB stamped on them but the documentation says QFAA-B00...
Is there a straightforward way to output the frequency of the 32.768kHz crystal oscillator to a GPIO pin? The motive for this request is to verify the crystal frequency without...
hi i have a question
i ues ncs 2.9.0
This is the code that displays my Bluetooth connection
——————————————————————————————————————————————————
struct bt_data ad[]...
Hello,
I'm developing for nRF54L15 the application with the NSIB + MCUBoot. I have a problem with fprotect in mcuboot returning EINVAL error. That happens due to limitation...
Hello, I am new to android development. I am building an Ble App for some of my work in which I want to include Direct Firmware Upgrade(DFU) over-the-air.
I have building...
Hi all,
do different settings of SAADC RESOLUTION register affect Conversion Time t CONV ? I cannot find any dependency - the only value given for t CONV is 2 µs typ (7...
My product has nrf52840 with usb mass storage configured using 8MB QSPI flash (same chip as the nrf52840dk - MX25R64)
I would like to allow users to upgrade firmware by...
Hello,
one of my project requirement is that i can accept data via bluetooth and rf. i want to know can we use bluetooth and rf in same code. the switching between bluetooth...
Hello there,
While investigating some issues with getting nRF Connect working on Ubuntu Gnome 17.04 , I came across a more fundamental problem.
I now have J-Link V6...
Hi, I successfully modified the Nordic Semiconductor SDK 13's SAADC example adding a feature that performs the FFT of the sample taken and using an RTC is possible also to...
Dear all,
I was following the "Getting started with the nRF52840 Preview Development Kit" page. But when i connect the board to the computer, the board do not appear as...
Is it possible to change the output power of the Thingy to +4dBm and how would one do that.
We are using the Thingy for demos and would like to demonstrate the difference...
Hello:
I have been trying to figure out the proper app ram address base by calling sd_ble_enable.
I am using keil's debug mode, and when the program hit the breakpoint...
Hi, I'm trying to view some logging out put using the segger RTT viwer whilst running keil's debug mode.
I can view some, incomplete loggins in run time (meaning not all...
I find NRF_UICR->PSELRESET[0],[1] can't be written to 0xffff when their values is 0x0015, but the values can be written to 0x0015 when pre values is 0xffff.
so, I can't...
I try to get rssi , but it didnt work. I tried to control what is the problem? , I just want that ; if there is any change , My red led will blink and then I will controll...
I am using Blend Micro with Nokia 5510 LCD.
Before applying BLE SDK for Arduino, LCD works fine.
After initializing BLE UART for nRF8100, send text through nRF8100 by UART...
sorry for short question
almost first step here. I came from eddystone format beacon to here
but I've found long time to add a sensor on nrf51822 module..
some articles...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
when i am load the the program to my nrf52832 with ble lbs example it show an error : Flash Download failed - "Cortex-M4" . my softdevice is s132 v3.0.0 .... please help me...
Hello everyone,
I have tested my prototype on nRF52840 but the board is pretty big and I want to do a product pilot with a custom hardware of mine. Now I know that the...
