void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
I am trying to program a QSPI flash with a file system. I have confirmed that my qspi ini is correct as i can read write and erase. I created a small file system on an usb...
Hello,
I would like to know if there is official C# source code to perform DFU OTA for a NRF52840 from Windows without Nordic hardware (DK, dongles etc..), using only the...
Hi,
I created a custom board following the instructions from https://www.youtube.com/watch?v=V_dVKgWKILM . Everything is ok and with the "Hello world" example builds without...
Hello,
after an attemp to switch to UF2 Bootloader from Open Bootloader my Makedriary nRF52840 MDK USB Dongle stopped working (now shows only the green led always on) and...
Hello ! I'm trying to adapt the code from the master-slave SPI example ( https://github.com/too1/ncs-spi-master-slave-example ) for my nRF54L15 development kit.
The master...
hello,
I would like to know which operations were performed on all chips by the `nrfjprog --recover` command.
"The nrf52833-B chip is by default enabled for read protection...
Hi
I am getting an error while building source code. The same code used to build while using NRF connect SDK version 2.5.1. Currently I am using nRF Connect SDK version...
Hi,
I followed the steps below and the error "zephyr\zephyr_pre0.elf section 'text' will not fit in region' FLASH'" appeared when I compiled. I did not change any code....
Hi, I am working on a Bluetooth Mesh project for lighting control using nRF5340. I am currently stuck on how to implement a Bluetooth Mesh gateway for my mesh network. Here...
Hi Nordic,
In my project, I have a NRF9160 and a NRF52832 with a ble host/controller stack over SPI HCI on NCS v2.5.2 As soon as I activate the HCI SPI in my project, the...
I have bought an nrf9161-dk and following the documentation, I was installing the asset tracker using nrf-desktop v.4.4.1 (because v.5.0 crashes everytime I open it in full...
Hi, We are using `fota_download` library on our nRF9161 design running mfw-nrf91x1_2.0.1 to download a firmware upgrade image from our Amazon AWS server location. When trying...
Hello, I am currently using (\nRF5_SDK_17.1.0_ddde560\examples\peripheral\radio\receiver)routine to develop.I want to check if the first N bytes of the received packet are...
Hi! I am using nrf32840 with free rtos,
and I have a loop that do the following
for(;;){
vTaskDelay(pdMS_TO_TICKS(intervalTime)); // go to sleep due to portSUPPRESS_TICKS_AND_SLEEP...