Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Hello,
I'm using nRF9151 as a HCI host and nRF52840 as HCI controller (nRF52840 config is based on HCI lpuart example). Recently I updated NCS to 3.2.2 and I started observing...
Hello, my name is dio.
I created an HCI UART application using nRF Connect for VS Code with NCS v3.2.4 and enabled the Channel Sounding component via the nRF Kconfig GUI...
I am developing a dual-mode HID device (mouse) using nRF54L15 with nRF Connect SDK v3.1.1 . The device determines its mode (BLE_mouse or ESB) at boot time via a GPIO pin ...
Hello,
I have designed a PCB with nRF54L15 SoC. Now the issue is that I have by mistake changed the MISO/MOSI pins of the device. As you can see in the following image....
Hello,
i have a custom board with a nRF52832 on it. TL:DR: i can't seem to get a connection to the chip via the SWD
When i try to recover the device it tells me the debug...
I want to flash an example firmware onto my nrf5340 board. I want to test le coded phy. So whych example should I use from the nrf sdk 2.4.0 to flash onto my device so that...
Hi,
there are several devices with same Firmware/Modem firmware/Hardware. All device were working. While all others continue to work, one suddenly gives me this:
Once...
In theory all driver calls are suspect, but for example I see crashes in nrf_802154_buffer_free_raw, at this assert:
This is easily reproducible by running 802154_phy_test...
Hi Team,
We want to load azure certificate into nRF9160, can you please provide sample code, code snippet to load azure certificate.
Regards,
Sravan Rikka
Summary
On NCS v3.3.0 , building any application that enables the new Zephyr OpenThread Border Router L2 glue ( CONFIG_OPENTHREAD_ZEPHYR_BORDER_ROUTER=y , together with...
Hi! This is a general info post since i have found a temporary fix to it, but whilst trying out ntn, we noticed that when switching from %XSYSTEMMODE: 0,0,1,0,0 to %XSYSTEMMODE...
Hi, we use BMD-350 modules (nrf52832) in our product which has been in production for over a year. Our DFU service is very well tested.
a couple weeks ago, while performing...
I'm planning to deploy a Thread network with 200-400 units and seeking best practices and real-world experience from the community. While the Thread spec allows up to 32 routers...
Hello Support team,
I have an issue with two simultaneous heaps in my project. I use nrf Connect SDK 3.2.2 with the next configuration options:
CONFIG_REQUIRES_FULL_LIBCPP...
Hi,
we are developing on nRF54L15 using NCS v3.2.3 , and evaluating a DFU architecture based on:
MCUboot
firmware_loader
main application
using the BLE MCU Manager...
