Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
A problem is experienced with our nRF52840 device, which occasionally stops working and cannot be reset.
Below are the issues observed:
The main software is stopped...
Good day,
I am currently working on adding support for the nRF54l15 SoC and adding support for multiple imu sensors to be connected at once. However, I have been unable...
Hi
I am trying to setup calude with nrf connect SDK and Visual code in windows.
Looking at page below , this is not really a step by step guide:
https://docs.nordicsemi...
Dear Nordic team,
I am struggling to set up CoAP with DTLS for a Thingsboard CoAP backend. The connection works just fine when using plain UDP, but when I set up a socket...
I currently have nRF52/53/54 Development Kits and would like to utilize their onboard J-Link debugger by connecting through the Debug-Out Port (P19). However, I have observed...
I was wondering if the nPM-FG schematic or board design is available, I'm interested in using it to profile a few CR123A's.
The docs suggest the firmware/schematic/layout...
Using nRF Connect SDK v3.4.1 with an nRF9151.
CONFIG_NRF_CLOUD_AGNSS currently has unconditional dependencies on:
depends on MODEM_INFO
depends on MODEM_INFO_ADD_NETWORK...
Hi, I am using nrf52832 with softdevice s112 and SDK 17.1.0
Is a ~14-15 µs latency between a GPIOTE PORT event becoming pending (via DETECT / LATCH , SENSE + LDETECT on...
Environment: nRF Connect SDK v3.4.0 on macOS Golden Gate 27.0 and Sequoia 15.8
Device: nRF9151-DK
Problem occurred during build and testing of AWS connectivity to AWS...
Hi
I am working with nRF Cloud - using a developer account (limited to 10 devices).
After connecting a few times with a device (using a different serial each time),...
Hello,
I am working with the nRF52833 using NCS v3.1.1.
I am using PAwR Scanner Role, and the device needs to remain synchronized while also allowing connections from...
Hi,
I'm using the Thingy:91 X PCA20065 rev 2.0.0 as a reference for a new nRF9151 design, and I have three related questions about BUCK1 and the 1.8 V rail.
1. nRF5340...
Hello DevZone.
Someone is asking for the switching frequency of DCDC in 54LM20B.
Using nRF54LM20A with nRF Connect SDK v3.4.0. The PS v1.0 documents VREGMAIN as DC/DC...
Hi,
1.Please assist me in creating the file "merged.hex". The example is "ncs v3.4.0 hello_world nRF9151dk/nrf9151/ns".
2.I have verified that both merged_nrf9151dk_nrf9151...
