I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
Hi,
I have twp device: one peripheral and one central. My peripheral is sending out high payload data continiously. And my central is sending data ()in 10Hz frequency. However...
Hello,
I'm interested in increasing the range I can get out of an Isochronous connection between two nrf52832 while maintaining about the same throughput. I'm not concerned...
Good morning,
In our next product (mounting a nRF52840) we will need a dual UART+BLE update channel. We have already implemented the update via BLE and we are now trying...
In SDK v2.6.1, commenting out the following code in websocket.c allows successful connection to the WebSocket. However, in SDK v2.7.0, even after commenting out the same code...
Hello! I have a Nordic nRF52840 BLE dongle, and I want to scan/sniff BLE air using custom BLE parameters: scan window and scan interval. How can I achieve this correctly?...
Hello,
I'm trying to figure out why GPIO 26 and 27 on the nrf9151 DK default to HIGH. I have my SALAE USB scope connected to several pins. When the board resets, only GPIO...
I am using an nRF52840 and nrf52832 to measure distance, but the reported value is almost twice the actual distance . For example, when the actual distance is 1 meter , the...
I would really like to use Bluefruit and make a Long Range connection between Servers and my Central. I know that it is not build in Bluefruit by default, but there must be...
Hello!
I'm using BLE Mesh sensor client receiving messages sent from multiple sensor servers. I used 2 nRF54l15DKs as 2 sensor servers, each sending 9 16-bit float data...
I have a problem with connecting to my device after i disconnect from it. I have tried ubond function, it does not work. This is my disconnect function:
I have a service...
Hello Nordic support,
My application is based on nRF5 SDK for Thread and Zigbee v4.2.0, with Softdevice S140 as I want my application to operate in either in BLE or Zigbee...
I'm trying to setup an SPI communication between an EVK of the Intan RHD2216 and the nRF 52840.
Browsing similar issues, I read the following topics already
I apparently...
I've been using the following SPI1M pins and they've been working:
But I have migrate away from these pins due to production PCB layout problems. The pins I need to...
I'm using nRF Connect SDK v2.7.0 with v2.7.0 toolchain to program a device with nRF52840 SoC.
When configuring task watchdog timer with hardware fallback an assertion fails...
