Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
I am using zephyr 3.1.0 and i build blinky pwm and rtc code from zephyr but it is not building i am using nucleo_u575zi_q board but in dts of board pwm and rtc is not there...
I modified the nrf9160 https_client sample to make a GET request to a web server and retrieve a JSON response. Unfortunately the rec_buf always ends up with an HTML response...
Hello everyone!
I've been struggling to get over this error when attempting to use an augmented Thread project based on the thread_mqtt_sn_client_publisher example. Would...
According the nordic documentation of the AT command +CEINFO, the value of CINR is in dBm.
Other source (outside Nordic) mention dB as common unit, e.g. LTE signal quality...
Hello everyone,
I'm trying to display internal sensor on NRF51422-DK (PCA10028) on my Android phone (v.12). I'm using Keil for programming and nRF Toolbox to see UART results...
ble_gap_addr_t xyz;
sd_ble_gap_addr_get(&xyz);
/**@brief Get local Bluetooth identity address. * * @note This will always return the identity address irrespective of the...
Hello, I have three questions that i could not clarify in an adequate amount of time via Google and DevZone.
Setup: I am working on a custom board equipped with nRF52805...
Good day
I am trying to use lwm2m_engine_set_float on the lwm2m_client sample to change the sensor value.
Referring to the above link, the sensor value is set in the...
I am trying to evaluate transitioning a product from the NRF52840 to the NRF5340, but we have a critical feature that uses specific functionality of the PPI. It seems that...
Trying to integrate memfault SDK to nRF SDK 17 segger embedded studio. But couldn't understand the below section. Can someone help with passing flags to linker and also adding...
hi,i use SDK17.02.
l use ESB RX mode, I need send the ack payload data, and I can only write it for 8 times. After I write it for 8 times, I use nrf_esb_flush_tx() to clear...
I am building a Thread Coprocess using the nRF Thread Coprocessor template . Everything seems to work fine except when I use the OPENTHREAD_MANUAL_START=n config in the prj...
hi dev.
I study ble uart.
and I succeed connecting with dk board(peripheral) and nrf tool box(uart).
and I also connected with dk board and putty. // like that computer...
Hello Community,
I am trying to test mqtt_simple sample on both of nRF9160-DK(nRF9160 SICA B1) and Thingy91(nRF9160 SICA B0). My hardware version: nRF9160-DK: 1.0.0 Thingy91...
