I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Greetings,
In our product, we encountered an issue when data saved in flash (FDS) that were previously retained are erased during DFU on some devices . This was indeed fixed...
Hi, I'm building an applicaiton based on ble_app_uart. I got that using idle_state_handle(); function to set the my nRF52833 into system ON mode. I disable system OFF mode...
Hi,
I am developing the nRF52833 DK with NCS 2.00.
I have successfully implemented a service to print the RSSI on the Android nRF Connect application. I use the function...
Hi all.
What is the best practice to set the system in standby? I have a PWM and when is active the system can be in a low power consumption until a button is pressed. But...
Hi,
I've some questions on nPM1100's buck regulator
1) What is the Iq (quiescent current)?
2) Does it support 100% duty cycle?
3) What will happen to VOUTB if VINT...
Hi,
We are using ANNA-B112 module with nRF52832 chip and trying to store the product serial number in UICR. From the description of UICR, it seemed that the CUSTOMER area...
Hi,
A have an application on a custom board that will not start, unless I use JFlash Start Application command, or attache the debugger. I already added CONFIG_BOARD_ENABLE_DCDC...
Hi,
given "nrf_drv_twi_xfer" or its "nrfx_twim_xfer" younger brother is used to communicate over I2C, and its a TxTx tranfer, than what does "nrf_drv_flag_tx_no_stop"...
I am using bleak and python to connect to a ble device and then using subprocess to run the dfu. The ble device disconnects when the dfu starts and then I get "Connection...
I have a Thingy:91 board that appears to be broken, no response either on the LED or via USB UART when switching on.
I've earlier done some development with it, and hooked...
Hello,
I am attempting to follow along with the AWS IoT example. Everything has gone OK so far (Create a Thing, Create a Policy, Create and download certificates) until...
Hi All,
In our product we have noticed that, on a few occasions, some important information that is saved using FDS (in a file with ID: 0x02) are being erased when an OTA...
Hi,
Do you have a recommended circuit for supplying VDD_GPIO with the right timing relationship to VDD?
Section 11.1 of the datasheet says "VDD_GPIO should be applied...
Since the 9160 will vary his transmit power based on signal strength, is there any way of determining what power is being used for a given transmission? I know that the max...
