I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Dear,
Would you teach me how to edit SES(Nordic version) on compile optimization level for nRF5_SDK_17.0.2_d674dde ?
I use SES 5.70a. I cannot found it in project options...
Hello everyone!
Has anyone ever implemented ANCS (Apple Notification Center Service) in ZephyrOS?
We are using nRF51822 SoC with the goal to connect to the smartphone...
Hi Nordic Dev community ,
using: nrf52840-DK SDK 15.2 softdevice S140 6.1.0,
Am getting a SoftDevice assert id=1 PC=0x17660 code=0x62D
App error handler id=1 PC=0x17660...
Dear Nordic Crew, I have got 5 adafruit feathers based on NRF52832 and nRF52833-DK so far. I would like to implement indoor localization based on BLE mesh and RSSI. As far...
Hi,
I am trying to integrate the Google IoT Cloud example into my CoAP Server. The example is using Secure API to esablish COAPS. I have enabled
CONFIG_OPENTHREAD_COAP...
I downloaded a project in named prj9160 from Github. The prj9160 had three folders : Azure, firmwre, mscerts. I run successfuly the following command :
west build -p always...
Hi everyone,
I want to run nrf_drv_saadc_sample in a loop but I do not want to use PPI and TIMER peripherals because they increases the power consumption of my device. I...
Hi , am working on mesh example from v1.8.0\nrf\samples\bluetooth\mesh\light_switch. In this example they are using generic on/off server , light LC server and other server...
Hi.
For example, for the nRF52832 BLE chip, could it, in some manner, be only visible/communicate with a specific/particular smartphone app? How? using the MAC?
Regards...
Hello, I have a nrf5340dk communicating with nrf52840 dongle connected to a pc with UART baud rate of 2M. Connection parameters are:
7.5ms Conn interval
1ms Slave latency...
Background The adxl362 driver native to the zephyr kernel doesn't support FIFO operations, so I built my own out-of-tree driver that relies on a new accelerometer API instead...
I wish to add a firmware version to my project. Because we are hoping to use OTA for updating I have set the configuration paramater:
CONFIG_MCUBOOT_IMAGE_VERSION
in proj...
After working with arduino's and microprocessors like the ESP8266 and ESP32, I recently started toying around with a nRF52840 dev kit. After going through some tutorials,...
Hello,
In my project i am using nrf52840 with my custom board and to upload the code through NRF_CONNECT application with soft device its uploading properly but with segger...
Hi, I have a problem configuring the PPP Modem correctly and I'm not quite sure what i'm missing here.
I'm running the code on a custom board. We are using nRF52832 to talk...
