I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi DevZone ! Here is my issue: I use to work with VSCode and nRF Connect for desktop for a few months now. Early on Monday, I did uninstall all my dev environment (VSCode...
Hi,
is there any way to get a Pin to a defined "high" without vdd-gpio ref?
In our situation the NRF9160 Power is a Battery with 4,1V and the VDD-GPIO is 3,3V with a regulator...
I created two build configurations a Debug and a Release in SES IDE.
Build > Build Configurations...
I wanted to select the DEBUG_OPTIMIZATIONS level for the Debug build...
This is a continuation of the topic here that is now closed
https://devzone.nordicsemi.com/f/nordic-q-a/85590/nrf9160-azure_iot_hub-change-dps-username-during-run-time ...
Hi, I want to update the modem firmware devices(in the field).I am using nRfconnect sdk 1.5.0 and hardware is brf9160 SICA B1 . current modem firmware is 1.2.3 . I tried to...
I tried to define an event as in attached figure. During Build, the error in the as shown in the attached imageoccurs. Where to define Log Configurations ? I ading custom...
cpu info:nrf5340
software:nrf connect sdk 1.6.1
hi professor,
In the uart interrupt I call k_fifo_put to trigger rx process thread but it is not take effect.What person...
Hi,
we are developing a system based on device with nRF52840 S140 ( central and pheripheral).
We developed on both side a custom service.
System is working fine bonding...
I'm new to the Bluetooth mesh world and I'm trying to change some basic configuration parameters during runtime, by modifying the Light Switch example. I've searched around...
Hello,
We are using Zephyr v2.6 and nRF51822 SoC in our project.
Because we are porting the code from the SDK environment into the Zephyr environment, we decided to use...
Hello everyone,
in the last chapter of
https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/getting-started/posts/nrf-connect-sdk-tutorial---part-1-ncs-v1-4...
Hi,
I have removed UART from my custom board dts file as in my current application, I am not using UART for any transfer.
But due to this, I am unable to compile code...
Dear Forum,
I already succeeded in using the Nordic Toolbox's DFU-App to update the firmware of a BM833 via secure bootloader. I found out, that the Android DFU App is available...
Greetings,
Which Bluetooth LE examples in NCS v1.9.1 are suitable for the nRF52810?
I tried the usual suspects. peripheral_uart overflows flash and RAM.
peripheral_lbs...
The documents for setting up and using a Matter network require a change to account for new behavior of the chip tools.
https://developer.nordicsemi.com/nRF_Connect_SDK...
