Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
I am trying to get a Holyiot 21017 dongle to work correctly as a Thread RCP. The Holyiot 21017 has a nRF52840 and a RFX2401c power amplifier. In VS Code with the nRF Connect...
I am working on a BLE project on the nRF54L15, and I need to add the FOTA over BLE bootloader to it for cpuapp_ns.
I am using NCS v3.4.0 which no longer uses the Sysbuild...
Hi everyone,
We are a research group at a university, working on indoor positioning systems based on Bluetooth Low Energy (BLE) technology. We are currently evaluating different...
For just a first test board off of Thingy 91x design, can nRF5340-CMAA be replaced with nRF5340-CLAA? What's the downside of doing that? Documentation says it's not recommended...
Hi,
I have a question regarding the transmission duration in the Online Power Profiler for BLE (OPP). More precisely, it is about the transmission duration during a connection...
We are experiencing an issue with the QSPI driver on nRF54L15 where external flash access stops working after a BLE bonding procedure.
The system works correctly until bonding...
Is there a sample project for the nrf54LM20A DK that uses the nrf_802154_radio_driver? We need to implement a custom protocol to work with existing products.
Thanks,
...
My VSC install is up to date, no updates pending in the Extensions manager etc.\
When building an app for nRF54L15DK I get a warning about the SDK being out of date, and...
I am using the nRF9151-DK as an SPI slave . The SPI communication is not working as expected, and the nRF9151-DK is not receiving any data from the SPI master .
I have configured...
Hello Nordic Support Team,
I am trying to upload firmware to my nRF54LM20B-DK using the nRF Device Manager application on my mobile phone .
For this test, I started with...
Hi!
I'm testing ubidots, which require a 35 character long username to connect with MQTT. This fails, and mqtt_connect gives me error -12 ENOMEM. The same code works fine...
HI,
As stated in the topic I have found several misalignments/issues in the following setup:
NRF Connect Desktop (v5.3.2) NRF Connect Desktop DTM (v3.1.4) NRF CONNECT...
nRF54L15: system clock stops permanently after a GRTC compare event is lost
Disclaimer
Claude Code (Opus 5) was used to assist with this investigation and with the drafting...
Hi, I just started evaluating the nRF93M1 DK (LABA version) and have questions about the firmware version.The AT+CGMR gives "mfw_nrf93m1_1.4.1", which seems to be a bit older...
We're based in India, developing a custom hardware board, and need to test CAT-M1 connectivity on-device. Since CAT-M1 coverage is limited in India, we're planning to travel...
