I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Excuse me:
I want to achieve t he maximum transfer speed between ble_app_uart and IOS NRF connect app，How to modify the example to achieve the maximum transfer speed with...
Hi
We are now using SDK v17.0.0 for our product and planning to upgrade SDK v17.0.2 because SDK v17.0.0 could no longer be downloaded.
But SoftDevice for each SDK is...
Hi all,
Background: -NRF5340 -NRF SDK 1.9 -Zephyr 2.7.99 My objective is to send via Bluetooth data of 244 Bytes every 10 ms per notify . For the tests, I use the dongle...
Hello,
I'm quite loss using the command nrfjprog.
I install in VSCode all NRF tools. It seems working good. I can compile.
When I have a look on "device tree" I cannot...
Hello,
We want to read external sensor data using uart in lwm2m_client project.
I tried below following code :
static char RX_Data; static char uart_buf[20]; static...
Hi,
I could see that in nCS path : "v1.8.0\mbedtls" , "mbedtls" library is provided, I need to understand what it does & how do I enable it for use in my applications...
I am attempting to build and run the Zephyr NVS sample ( https://docs.zephyrproject.org/latest/samples/subsys/nvs/README.html ) on the 52840 using the nRF connect extension...
I have an Adafruit nRF52832 board, and I'm trying to minimize power consumption by putting it in system off mode. It is attached to a breadboard, and none of the pins are...
Hi Nordic Team,
I noticed a potential issue while migrating from SLM v1.4.0 to v1.9.0. In addition to the inversion of the <state> representation in #XHTTPCRSP introduced...
I have developed a Zigbee application using the nrf52840 DK board + nRF Connect + Zephyr and it is working. Now I am trying to move that app over to the nrf52840 dongle. It...
Hi, I am using nRF52832 development board and I have a motor driver. Motor driver has external power supply, I am just using nRF52832 to set directions which consumes low...
Hello, I am trying to use the dfu library to update the nrf52840 with a firmware stored in a littlefs file in an external qspi flash. I can successfully read the entire firmware...
Dear Nordic team,
it is very important for the RF and the HW engineers to be able to know the current transmit power of the modem. That will help us evaluate the network...
