Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
We've developed an application based on nRF52840 (via Raytac module MDBT50Q), utilizing the Adafruit Feather Express Bootloader as our basis to simplify the development. Our...
Hello.
Log data is transmitted to APP(phone) using sd_ble_gatts_hvx().
The length of one packet is 20 bytes, and the expected total number of packets is about 3,200...
Hi folks,
Looking at the nRF Command Line Tools download page , I can see versions of the nRF Command Line Tools for Linux, MacOS and Windows. The Linux versions come...
Hi everyone, I would like a bit more insight and recommendations around the following list of SDK_CONFIG options. The description is not clear enough and I don't understand...
Hi, I am using libuartes to comunicate with gps and I get the Rx buffer like a problem already asked in this thread when I send a text "abc"
the first 3 times : everything...
Hello,
- If I supply nRF52833 in High Voltage mode (LDO + LDO sub-mode, not the DC/DC convertor).
- Set the VDD in the corresponding register to be e.g. 2.7V (VREG0 LDO...
Hello all,
this is actually repost of the previous post : Porting the library code of the sensor due to my fault, somehow I have clicked on the the wrong button ...
Anyway...
Hi,
Our product is using nRF52810, and we need DFU. But the size of application Bin is over 60kbyte(about 63k). When we use S112(100K), the bootloader is 32K, so we just...
I am using:
nRF52840DK nRF5 SDK for Thread and Zigbee v4.1.0 CLI example with added code Border Router on Raspberry Pi 3+
Using the CLI, I can get an IPv6 address for...
We would like to use the nRF52840 to upload compiled Arduino firmware in hex file to atmega328p over serial port.
The latest version of the Arduino firmware would be stored...
nrf52833, custom application based BLE Central Uart Project.
s140_nrf52_7.2.0
Our average Power use in the application is 1.5mAmps. What is the proper way to manage...
Hi, I am working on ble_app_uart_c(central device) and want to add the DFU option. I have successfully added a buttonless DFU service in the peripheral application. Now how...
I'm testing a simple application based on the UDP example. It samples some peripherals and ADC channels, these values are then packed into a CoAP message. This CoAP message...
Hi,
My custom board using nRF52810, project was based on ble_app_uart_pca10040e_s112 and secure bootloader.
The size of application is 59k, and the bootloader is 32k....
Hi
I looked in the nRF9160_PS_v2.0.pdf，I can not find the voltage level of SPI signal pins，Does the voltage level of SPI signal pins equal to the voltage supply to the VDD_GPIO...
