Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
Hi Nordic Team,
I am working on a project where I am using an XBee module as the Zigbee coordinator in a centralized network and an nRF52840 (running the ZBOSS stack from...
Hi everyone, I have a problem when I configured custom board GPIO UART in NRF54L15. I know that the NRF54L15 have UARTE00, UARTE20-22, UARTE30. I just use 2 GPIO ( UARTE20...
I use the app_gpiote_user_register to set GPIO port 1 pin, but this registers only 32-bit mask, so it can only to setting port 0.
If I want to use the port 1 pin for app_qpiote...
Hi!
I'm attempting to run the application from this URL , but nothing appears on the serial console, and I don't see any posts on the toilet website.
Could you help me...
Hi,
I am using an nrf5340DK + nrf7002EK. i am able to run an example helloworld application with an immutable bootloader and mcuboot as platform bootloader. When i try to...
Hello! Recently while performing a BLE firmware update using the mcuMgr Library, the stages of the firmware update are as follows VALIDATE, RESET, and fail on UPLOAD. When...
the code below successfully complies and returns 3 services with 1 characteristic each, I have copied the uuid for the primary services and characteristic and that doesn't...
Our board is based on nRF52833, using SDK 2.1.2, Zephyr 3.1.99 Project is configured to enter low power mode for both CPU and peripherals CONFIG_PM=y CONFIG_PM_DEVICE=y Our...
Hi,
After downloading any of the projects from nordic github, how does one compile the project successfully? Where should i extract the files to and what paths should i...
HI.
NRF connect For Desktop Programmer program Fail.
So I used command Tool (nrfjprog). command Tool worked.
Enviroment:
- nRF Connect For Destop v5.1.0
- Programmer...
We're attempting to provision one of our nRF9160-based IoT devices to our AWS VPC.
We're following this procedure:
Provisioning our eDude on AWS
Step 1: Provision the...
I'm trying to get FOTA updates working on the NRF54L15 DK. I noticed there isn't a dedicated guide available for these yet so have been using this page: https://docs.nordicsemi...
I’m encountering a build issue with Zephyr (version 3.7.99) on my custom board based on the nRF52840 SoC. The build process fails during the linking stage with an undefined...
Hi ,
We are using MCU nRF52832-QFAA-R (Flash 512KB & RAM 64KB) with softdevice s132 - 6.0.0.
I am not sure what is extracly Soc Revision of the MCU ? But I read some information...
