I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Trying to compile samples/net/wifi/ to test the esp8266 with Nrf52. we have our custom board. but Im' testing using Nrf52840 DK now.
I've this file
in myProject/boards...
We have a custom PCB with GPS circuit copied from the NR9160-dk board.
The default GPS example is working fine. However, we want to combine GPS tracking and LTE-M connection...
Hello,
I am using NCS 1.5.0 and modem firmware 1.2.3.
I have nRF9160 DK version 1.0.0.
I am trying to run "full_modem_update" example firmware on this.
But getting...
HI
I use NRF9160 serial_lte_modem to test NBIOT/MQTT, current SDK is V1.6.0 ,and config mqtt keepalive =1200S.
after 9160 connect net, control mqtt connect my mqtt server...
I have connected 3 Peripheral using Name Filters and 1 central.
I am able to connect and communicate with all correctly.
But I need to identify that conn_handle 0x0 ,...
Hello!
When collecting dc1.4v with SAADC, there is an error of 100uv. SAADC is configured in differential mode, with N-terminal connected to GND and p-terminal connected...
Hi,
I've read in these forums and seen the machine instructions within the C code that nrf_delay_us (which BTW is used to do nrf_delay_ms) is implemented by executing a...
Hi team,
I would like to know the default channel used for data transmission and the frequency of the channel.
Also whether the frequency is configured in the softdevice...
What is the purpose of the external capacitors on DECA and DECN? DECA calls for 1uF and DECN calls for 0.1uF. The datasheet calls these out as "Regulator Supply Decoupling...
Hello,
sorry to border you again, but I have a problem that block me for many days. I read all nordic questions on TWI (I2C) but did not found a solution... :(
I have...
Hi,
We are designing a custom Board using nRF52840 SOC.
We are operating it in Normal mode, using an internal DCDC converter
We have used configuration 5 from the...
Hi there,
I need to transmit 33995520 bytes from nrf52 peripheral device to a Windows/Android device. Currently it takes about 13 to 14 minutes to complete the data transfer...
the flash of the nrf52832-QFAB is 256KB. the softdevice S132 is used which consumes 152KB and the compiled file of the BLE_UART only consumes 98KB (after making the changes...
