I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hi, There. I am preparing to program a Mesh application based on nrf52840. The application supports the recovery from the points of power off.
So, I have a question. It...
Hi,
I'm working with the peripheral_uart example in ncs 1.6.1 and wanted to enable flow control for uart0, but do not see a way to do that.
How do I enable flow control...
Hi, There,
I develop a communication application based on a beaconing example on nRF52850 DK.
I don't know where I do wrongly. It is always stuck in the "bearer_handler_action_enqueue...
Hi,
I'm trying to collect modem trace from a custom nRF9160 board which is connected to the PC with a FTDI FT2232 UART-USB converter (USB vendor id 0406, product id 6010...
All - We have an nRF52340 based design which when tested with the system off demo available in NCS v1.5.1 gives a system off current of <1uA.
We have a second design using...
Hi.
I just downloaded the new nRF5 SDK v17.1.
The first example I tried, the ble_app_template, the Keil uVision project for pca10056 is setup to use a fixed device pack...
Hello,
We are using an nRF52 DK as part of our QC process to send test commands to one of our devices and record responses. However, I think that the people running the...
Hello! I'm reading the documentation that exists for the nRF5340 and struggle a bit about the Secure attribute unit (SAU) If you read the ARM documentation about TrustZone...
Hello.
I am developing Central device which support LESC.
I have some question about connect to Servers which have diferent LE security
for example case, one of...
Hello,
I am using nrf sdk 1.5.1 and trying to connect the Nrf ZigBee router(light bulb example) with Digi Xbee Coordinator but it doesn't seem to connect. I observed the...
Hello all,
I'm interacting with some nodes in a test network:
setup: 10x nrf52840 DK (PCA10056) boards loaded with the following software.
1x Coordinator ( Zigbee CLI...
Hello,
I'm using nRF SDK v1.6.0 with nRF9160 development board. I did minimum changes to Asset_Tracker_v2 application (enable debug log, set up for my aws account and to...
Migrating from nRF5 SDK to nRF Connect (Zephyr) what is the best way to define pin names using a custom board? in nRF5 SDK the header file custom_board.h usually defines the...
If I enable CONFIG_ASSERT=y this example will crash (or code using the DF APIs)
To reproduce:
- nRF Connect 1.6.1
- In direction_finding_connectionless_rx add CONFIG_ASSERT...
HI Devzon
currently my customer has some question about the power consumption difference between "LOWLATENCY" & "LOWPOWER" on NRF5340 GPIOTE
we useing PPK2 to testing...
