Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hi,
I am storing sensor data into flash and sending it to client when it is requested by Indication characteristic.
I don't have any issue with reading/writing/updating...
Hello developer,
I am new here and learning Beacons with the Board nRF52840 Feather from Adafruit as scanner and Segger Embedded Studio. I refer to nRF52 SDK 17.0.2 and...
Hi all,
I have connected my PPK II to my pc (Ubuntu), installed the software and connected the device.
I can't seem to find the mode or start button anywhere on the user...
Hello everyone,
I am using the fanstel BC840, where the tx and rx pins of the uart are alloced on 1.02 and 1.01:
So i have created a custom_board named hello_board...
Hi,
I’m trying to test/confirm the accuracy of the 32kHz crystal oscillator and the 32MHz crystal oscillator by toggling a GPIO at a derived rate and at 50% duty. But I...
The tag options did not include just nRF Connect as an option so I picked something that had nRF Connect in it. This issue has nothing to do with the SDK.
This is a question...
Help me simple LED Blinkink nrf51822 AA type i'm using YJ-14015 and stlink compiler.. i'm also using keil for IDE. i don't know how to create program and setting for compiler...
Hi,
Using nrfutil tool to transfer firmware package on Windows 10 system is much slower than on NRF toolbox on Android phone. How can we improve the transfer rate of nrfutil...
Hello, when trying to program a custom board with an NRF52805 with a J-Link from SEGGER Studio using one of the examples for the board "nrf52dk_nrf52805", I get an error saying...
Dear Devzone,
At the moment, We do not have methods to measure the GPS sensitivity of our products based on nRF9160.
We are using an active antenna with LNA gain 16dB...
We are using the NRF52 as a SoC in a sensitive analog application,
I need to model power supply noise created by the DCDC convertors REG0 and REG1.
Is there a SPICE model...
Hi Nordic team,
My dev environment is as follows:
nrf52840 + s140 +SD6.0.0 + SDK15.0.0 + SES + nrf52840-DK
Here, nrf52840-DK is configured as BLE Central and my peripheral...
Hello,
I'm trying to develop a ble-uart gateway based on mesh provisioner and peripheral-uart samples but i'm getting an error on getting the device bind of the uart device...
Our original BLE stack application on the nrf52840 has integrated encryption. It uses LESC with MITM and bonding.
I have gotten a certain level of run time success with...
Hi, I cant get access to my custom nrf52840 board after I click "Erase all" in "Programmer" in "nRF Connect for Desktop". This custom board has been working with me for at...
