Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi,
I work with win10 laptop, Toolchain nrf Connect SDK 1.6.1 on a nrf5340dk.
I try the sample peripheral_lbs, I can use the BTN1 to turn on a led when I push the button...
Dear all,
Another quick question.
What is the purpose of antenna LC network on reference design specifically? Does it meant for impedance matching or harmonic suppression...
Hi there,
Let me ask a question regarding signal strength.
Every cell phone shows signal strength with the number of bars on the top right corner.
I am wondering how...
Hi,
I am using nrf52832 custom board and sdk17.2.0.
My application is a Freertos application. I see that my application is going to hardfault from _start without entering...
Device: nRF5340PDK
So i have the same Problem as described here https://devzone.nordicsemi.com/f/nordic-q-a/74483/bluetooth-examples-are-in-infinity-loop, but i flashed...
Hi, I have enabled DFU in my custom ble_hid_keyboard in NCS v1.6.1
when i copy the same project and placed in another name after that build successful but while running...
Hi,
I have merged these two codes from SDK:
\nRF5_SDK_17.0.2_d674dde\examples\peripheral\timer
\nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_beacon
I want...
Hi,
I have nRF52 dev boards (nRF52840) (PCA10056), I am using SoftDevice nRF5_SDK_17.0.2_d674dde.
I am not sure SoftDevice SDK 17.0.2 supports BLE 5.0 specification: ...
Hi I am using Ncs version 1.6.0 and nrf52840dk ..BT_HCI_LE_SCAN_FILTER_DUP_ENABLE this duplicate filter enable is not working in NCS.is there any workaround for that?
I have a question regarding the power sequence mentioned in the nRF52833-Dk guide:
or the power sources section the guide explains it as:
I drew the...
Hi,
I know that this question was asked before, but I can't find a complete/recent answer.
We are trying to use nrf52 DK board to perform bluetooth localization. In...
I have a few questions about the bootloader of the nRF52.
I used "nrfjprog --eraseall" to erase the chip, afterwards I turned the power off and on again while holding down...
Dear Community,
I implemented the beacon-example with S112 and 1MBit mode and with S140 and coded-phy 125k sending one beacon per second continuously at +0dBm (sd_ble_gap_tx_power_set...
I have attached a sensor board to the nRF5340DK board I'm using zephyr 1.6.0 on macOS
I ran an I2C scan example using I2C1 peripheral and it works fine
found 5 I2C slave...
Hello, I have an issue. When I disconnect device I need to know it's mac address. Can you answer, how do i can get mac address of disconnected device or list of mac addresses...
