Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
When implementing Shell NUS option we've faced with the following: NUS transport takes in account only 'enter' symbols and doesn't react to ones like up-arrow, down-arrow...
The interface "sd_ble_gap_adv_start" uses "adv" to indicate broadcast, but the interface "ble_advertising_start" uses "advertising" to indicate broadcast. Why not use the...
Hello Nordic Team,
I am trying to flash the existing BLE light example code to my BL653 kit with Segger Embedded Studio. After falshing the code into the board it is taking...
Been having trouble integrating systemview for tracing FreeRTOS application. I came across this thread , and even tried replacing the files with what's inside the PatchedFiles...
Nrf Mesh App Version 3.1.6
After provisioning 2 nodes, I connect to one as a proxy, whenever I try to "get TTL", "Read State", or refresh the configuration server after...
opened nRF connect and attempted to open the dongle with this. When I plug the dongle in without holding the button, i get this error
2021-02-14T20:18:30.648Z INFO Using...
I am unable to generate setting using nrfutil.
Command used is as follow:
nrfutil settings generate --family NRF52840 --application pca10056/blank/armgcc/_build/nrf52840_xxaa...
Hi
I'm trying to use the LIBUARTE library together with BLE_NUS example in SDK 17.2.
From the libuarte sample I add these lines to NUS example:
I also modify sdk_setup...
Hi!
I am trying to flash some Zigbee related code to experiment with creating DIY smart devices (specifically Zigbee and matter ones) using my Arduino nano 33 BLE. One problem...
Hi,
I flashed open_bootloader and it seams to work. I was following this question . However, after building application (I am using ble_central/ble_app_gatts example), creating...
hi,
im using nrf52811 customised board,for long range purpose im using softdevice s140
so i need to port secure boot loader pca10056 to pca10056e
can you please me reagarding...
Hi,
I have tested the ble_nus code in NCS v1.4.2
where i can't send 250 bytes
I want to send 250 bytes to ble nus data send for 100 ms once
How to enable data send...
Hello,
I use the nrf5340 pdk. I would like to flash the led1 with a duty cycle which is different from 50%, so i tried to open the binky_pwm project, but the segger shows...
Hello,
what is the correspondence between the number of pins indicated in the dts file with the port number and bit of the chip.
for instance:
& spi1 {
compatible...
