I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, I am trying to code an AoA transmitter using the direction_finding_connectionless_tx sample project as a basis. I am using nRF Connect SDK v1.6.0 with nRF52833.
I am...
Hello,
I am having a few problems when trying to check if the nrf52 is dfu mode with my python script.
For that i was trying to get the firmware version from the dfu...
On Mac OS X Big Sur using the nRF Connect 1.6.0 installation in Segger the documentation suggest that to add a new source file to a project one should right click the project...
Hello, I tried to run the following command on my nRF52832 today and it reported an error.
The operation before the error was: I enabled APPROTECT, and when my colleague...
Hi, I made a mistake while working with a custom board.
I run "nrfjprog --recover", which obviously clears UICR, and then I powered the board off without writing the new...
I have a custom board with 3 nRF52840 chipsets, 1 central module is connected to 2 side modules.
The central module communicates with each of the side modules using UARTE...
Hi!
There is an end device that measures the temperature. If I calibrate the ADC during initialization or immediately after startup, the program hangs. If I start the calibration...
Hi Team,
I am trying to make RTT in debug terminal instead of debug serial port i was add all rtt files in the project tree but it was not shown in cmsis configure wizard...
Hello everyone,
I am trying to implement ECDSA_P256 in my code by using the nrf_oberon libraries.
What I have to configure in order to use these functions?
Regards ...
I use nRF52810 SoC to forward data between BLE and UART on our product. So I initialize UART interface and set some GPIOs once enter the "main" function in my codes. But we...
Sdk: 1.6
Modem fw: 1.3
Hi,
I am testing the GPS + supl example on our custom board. I am sitting indoor close to a window so satellite reception is affect.
the example...
Hello,
I am Working on the nRF52840 custom board.
To drive the motor and buzzer I am using a PWM driver in that when I set duty-cycle 20 percent then the output of PWM...
Hi guys,
Using the PPK 2 board I have noticed that sometimes my device does not go into deep sleep mode between two tasks. I had to implement a lot of flash operations using...
Hi Team,
Currently we are using 52840 soc with softdevice s140_nrf52_7.0.1_softdevice.hex.
We want to migrate to 5340 for BLE 5.2 features, we would like to understand...
