I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello i have a keyboard with nrf52840 with ZMK firmware, BLE, adc, gpios, i2c0, usbd, DCDC and CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC
When it is connected with the computer...
I would like to know the natural interrupt priority among different peripherals of nrf52840.
Specifically I am looking for default interrupt priority between RTC1 and TIMER1...
Hello, guys. I'm using the PCA10040 and the SDK 16.0's BLE UART peripheral example. I am trying to make PWM signal below.
When PWM0 stops, PWM2 works, and when PWM2 stops...
Hello everyone,
I am working on an nRF52-DK and getting familiar with Zephyr. In this process I am currently trying to extend the BLE MTU size beyond the default 23 bytes...
Hello,
My device is a USB HID peripheral connected to a PC. There is a case when the PC is turned off, but USB power is present. I want to detect this situation.
At the...
Is it possible to detect the presence of a Low Frequency Crystal and configure softdevice to use if present, otherwise use the internal RC oscillator?
A proposal would be...
Hi,
we have troubles to use 4wire NRF LPUART between nRF52840 (client) and nRF9160 Serial LTE Modem app (server).
We use v1.5.1 of nRF Connect SDK.
For nRF9160 we added...
Hello Team,
I want to know while Ble device is connected to the android device and within 5mins if device not get any data from android device then,
- Can device enter...
I am using sdk for mesh v.5 (s140.7.2.0) and nrf52840 DK and want to add uart peripheral into the client in the light switch mesh example and then trigger button 1 once a...
Hi,
I have written Hitachi AC IR transmitter using Smart remote 3 library.
Smart remote 3 library support 2 AC protocols, i.e., SIRC and NEC.
Kindly guide me how...
Hello, I essentially want to figure out a way to use the NFC buffer received by code like the writable_ndef_message example and have that same buffer, in the same code, advertise...
Hi
the new nRF9160 Modem FW 1.3 supports Non Ip Data Delivery (NIDD) on NB-IoT In nRF Connect SDK, there is a new example that can be used to test some modem functionalities...
develop tool is nrf5340dk and sample peripheral_uart in NCS1.5.0 ,when debugging , function uart_cb() alway run in case UART_RX_DISABLED and case UART_RX_BUF_RELEASED
,code...
