Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Hi, I am trying to achieve the lowest current consumption possible on the nRF9160-DK, which should be about 1.4 uA in modem shut down state. Unfortunately, my best result...
Hi all, I want to form a thread network.
I have BorderRouter [Raspberry pi 3B flashed with Nordic alpha 4.1.0.1 image + nrf52840 dongle in NCP design] and is up and running...
Hello.
This issue was tested with nRF5 SDK v17.0.2.
There are steps to reproduce :
sdk_config.h should not be included in nrfx_clock.h. It's a default template by...
Hello,
I am looking for some help solving a peculiar issue with eddystone beacons, the nRF52805, and some cheaper Samsung android phones.
System Description: - I am using...
Hello,
I have been running this program without any problem then I added some code to read and write to flash using NVS when the error shown below appeared.
I am running...
I have been using the Toolbox to load zip files to a device. Now the toolbox uploads a file and 'say it is complete', but the file status in the menu window say file not loaded...
Hi forum,
I am working on nrf52832,using sdk15.0.0.
I referred TWI_sensor example as reference for sesnor interfacing. Individual sensor works when i trired to integrate...
Hi,
I am using an NRF 51422 DK, SDK 12.3, and Soft Device S130. I am also a beginner to development with Nordic Products, and RSSI collection in general. I am using the...
Hi Nordic team, I'm working with nRF52840 PCA10056 , base on Thread_Zigbee_ v4.1.0 , and light_control example. I modifed, try to add temp_measurement ZCL in all light_bulb...
Hi ,
My environment:
nrf5340 dk board
nrf connect sdk
segger studio IDE
.
I want to test spi loop back without any connections.
I don't want to connect any...
Hello, zephyr pwm driver documentation and samples , shows clearly how to generate a PWM output using nrf52840 dk. However, we need to synchronize the PWM output to an input...
Hello, how can we configure the counter in an nrfx52840 dev board to count pulses on an input pin in zephyr? There is a counter driver in zephyr, but there doesn't seem to...
What I'm trying to do, is probably very simple. I hope.
In the following code which works fine.
I want to scan not using Coded PHY
Then change back to using Coded PHY...
question here, I am using nRF52840 device with zephyr application & MCUboot + SMP service the DFU is now done using: https://github.com/apache/mynewt-mcumgr-cli or using Nordic...
