Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hello,
I am using nrf52832 and I just have 3 questions regarding it.
1) SAADC change over temperature. According to the datasheet, it has a change of 0.02%/C but I only...
Short version: can I use a pin both as a GPIO input to trigger GPIOTE PPI event, and as SPI MISO *at the same time*?
Detailed version:
I want to use the SPI peripheral...
Hello everyone. I want to turn the LED on and off with the push button, if I want to hold it down after 3 seconds the LED will turn off, if it has been pressed for less than...
Hello
I am trying to port a custom project for nRF52840 from Keil to Segger Embedded Studio -uVision V5.33.0.0 -Armcc V5.06 update 7 (960) -SDK 15.2.0 -Device Familly...
SDK version: SDK17.0
We have low received radio message count with open USB CDC compared to when it is closed.
The low rx varies from 20% to 50%.
USB open = screen...
Hello!
what command should I send via BLE to disable the pressure, gas, and light/color intensity sensor?
In this documentation: nordicsemiconductor.github.io/.../firmware_architecture...
Hello
Assuming I set FDS_CRC_CHECK_ON_WRITE flag in sdk_config to 1, where do i get a notification that somthing went rong? I probably miss something but I need to clarify...
I'm using nRF52 DK BLE.
In the code, I used the following code to set the Tx Power = +4dBm.
On my HUAWEI Android phone, I use the nRF Connect app to see the RSSI. My...
To test the example, I downloaded the project through the following path.
https://github.com/NordicPlayground/nRF52-ADC-examples
I get an error like an image. What should...
Hi!
Hope you are doing well!
I am developing a BLE device and right now I want the device be able to auto reconnect to the phone.
e.g. The user leave home with...
Hello
SDK = ver 17
DK = nRF52
Using Peer manager for writing peer data in flash and FDS to store app settings in flash.
1. They both share the same spcase in flash...
Hi,
We are in the middle of product certification, right now with BT SIG testing. Unfortunately we got stuck right away since the test house cant configure the device...
