Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
hii this is rohit vekariya from bluesys lighting solution.
i am new in nordic can you provide example code for drive neopixel(ws2812) using nrf52832
thanks
I set up nrf52832 that it is proxy device, i create a loop that proxy device sent 20 message to app phone (Android) within 100ms. But my app (Android) receive only 1 message...
I'm designing the nRF52840 into a new product with BLE, LTE and GPS.
Could you please point me to a recommended matching network and antenna solution for the nRF52840? ...
I connected a button to LED on a breadboard, how can I write a debounce function to control a button. I checked app_button.c but it seems buttons they are using is button...
Hi, We have a custom design using an nRF9160.
We can connect and program the device using a jLink though the debug port.
How can we connect the LTE link monitor to the...
Hello everyone,
I get the following error whenever I try to build an application for the thingy91_nrf9160ns board:
The secure version works just fine.
For some...
Hi Team, I have design wireless node for biomedical application. I have used nRF51822 module in my PCB. I want to see the real-stream data from sensor (connected in input...
I am getting an error like this. I did not understand what it meant. could you help me please?
<error> app: ERROR 8 [NRF_ERROR_INVALID_STATE] at D:\1_1_xxx_xxx_xxx\V.1.5...
HI:
I Use the Projtcet: "......\nRF5_SDK_15.3.0_59ac345\examples\ble_central\ble_app_uart_c".
In the BLE_Central project, how to set the Tx Power??
thank you very much...
Hi , when i first recived my nRF5340 DK it had an preinstalled code that maked the leds to fade depending on what button i pressed, but now when i try the example codes on...
Hi,
We're running the aws_iot example and it would seem that by default it does not use the certificates in the file certificates.h
Is that the case and how can we use...
Hi,
I'm new to the whole Nordic environment, and I need to develop an application working with ble and lteM, so I have an nrf9160 DK for this purpose.
I worked with the...
I have a custom board based on NRF52811. Salient features:-
Both HF and LF crystals are present on board.
Power supply is 3.3V.
MCU DC-DC is enabled.
I am using...
Hello.
I trying the test for real time transfer a data.
Period is 4 ms and 5000 point data. (Total 20 sec)
The GPIOTE event occurs every 4ms and the processed...
