Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hi Dev team,
I am working on a Thingy91 device, and I am sending data out through MQTT.
I need a functionality to send some commands to do assigned tasks from the MQTT...
Hello everyone,
I am simply looking for some clarification on how to correctly handle button presses on the nrf52840 DK, as there seems to be multiple ways to go about it...
Hi,
I'm trying to build a working example of an aplication that uses the ANT+ softdevice (either s210 or s212). I already found out that the PCA10028 and PCA10031 (my board...
Hello,
This is more of a C question and I am new to Embedded C programming, I have this question.
I want to know how to access the flash memory without fds or fstorage...
Can we use beacon as a broadcaster and observer in thingy 52? Please suggest the way how to enable led indication using the distance generated from RSSI value and the data...
Hello,
When I use the " west update" command to update ncs1.4.99-dev to ncs 1.5.0, the following error occurred. How can this situation be solved?
Thanks.
BR,...
Hi, i am electronics engineering student and i have a project with nRF52832.
I want to design NFC antenna on PCB but i have not a experience and information about this topic...
I use custom board nrf5283 ..
Getting the following error while trying to flash
ERROR: JLinkARM DLL reported an error. Try again. If error condition ERROR: persists, run...
SDK: 4.1.0
CHIP: 52840
old question
my sleepy zed lost connection to the coordinator after refreshing key of the coordinator.
1) how can I manipulate refresh...
Hi All,
Is there any proper method for updating the firmware via serial port of nRF52840. The same process as arduino or esp32. Can we invoke the updation process with a...
Hi Nordic Team,
Summary: Please guide to open and build simple example nRF5340 project using Segger IDE on Windows 10
Details:
We tried to have Segger IDE setup for...
I am trying to compile a sample application for the Board nRF5240 . While i install the nRF Connect SDK for ncs v1.5.0 through Toolchain Manager 0.9.1 , I get the error as...
HI,
Is it in anyway possible to change the maximum gazelle payload size to 64byte instead of 32byte, I need more data when I send data return to the device.
Hi.
I am working on the MSC, and starting with the usbd_msc demo. The windows explorer will show a disk named "USB Drive" if connect to the PC.
I would like to change...
