I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi,Master:
Question：
When the finished product cannot be debugged with jlink, I want to save and trace the function stack information through the firmware. When there...
Is it possible to merge client and server to one image using ble_uart Example?
Which could work as client ,also as server ,it controlled by program.
Thanks a lot.
Hi,
I'm using the NRF52811.
In my schematic, the SWDCLK and SWDIO is connected to an external connector and the NRF52811 is connected to MCU through the SPI channel...
Hello
I'm having problem with UDP reception. I'm using nrf9160 with modem firmware 1.2.3, nRF Connect SDK v1.4.0, LTE-M.
I can receive UDP packets in the device as long...
Hi I am designing an intercom and I need help related to it. The following are the requirements of my project. I need an intercom module through which two-person can communicate...
Hi
Now I have a PCA10040 board and MDBT42Q board. I intend to transfer data between two boards via ESB TX and ESB RX example. However, with MDBT42Q I used nRFgo Studio to...
Hi,
We would trigger button to send zdo_mgmt_leave_req to coordinator for leaving the group.
When coordinator is not on power up, we would receive the 0xFF at callback...
Hi,
I want to calculate throughput rate using data that nRF52840 dongle working as sniffer captured.
Wireshark shows 'time' , 'delta time' and 'packet time'.
I think...
Hi,
I have serval questions about TX power settings.I wan to increase power to +8dBm,but the result is no effect.
1 Before reseting Tx power,call nrf_802154_tx_power_get...
Hi There,
Custom xamarin bluetooth app [using Plugin.BLE] is failing to connect to the device using ConnectToKnownDeviceAsync approach. User uses tap-to-pair and tries to...
Hi ,
We have a requirement to use the end device. The device should be an sleepy end device normal . When we want to transmit a large data to router , we want make this...
Hi Sir:
I am using SDK nRF5_SDK_17.0.2,the chip is nRF52810. Using the ble_peripheral\ble_app_uart.
The IO is using P0.6 as the BLE Uart's RX Pin,And P0.7 is used as BLE...
Hello, I was successful in using Arduino headers/ libraries to program my nRF52 DK, but now I am attempting to recreate the project in Segger V5.34 for MacOS for potential...
I want to use 52840dk to implement a file system to save some data. I am using NCS V1.4.99. I tried two samples , v1.4.99-dev\zephyr\samples\subsys\fs\littlefs and v1.4.99...
