Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hello
I need help, I have a problem implementing ppi gpiote and spim. The ADC I use is mcp3562 which sends via the irq pin when the data is ready. I need to work in continuous...
I used Nordic52480 DK(bulb) as DUT to run Matter Certification case TC-DGGEN-2.1 .
Steps:
1. setup OTBR on Pi4：./certification-tool/backend/test_collections/matter/scripts...
Hello I have an nRF52840 board with a 2 MB external flash I'm using SDK 2.6.2 I'd like to configure the mcuboot_secondary partition to be on the external flash
Here is my...
Windows 11, VSCode, NCS v2.3.0
Hi, I have a well-working application that I would like to build ztests for.
I'm reading about how to do that on the test framework page...
I often see the following warning when requesting a GNSS location: "<wrn> location: PSM is configured, but modem did not enter PSM in 2 minutes. Starting GNSS anyway." - what...
Hi everyone,
We’re currently using the nRF9160 module with JIO Nb-IoT SIMs in our devices. Could anyone clarify if any specific actions are needed in the firmware for...
I have an nRF54l15-PDK dev board (brand new):
I did the following commands with the SDK v3.0.2. Building and Flashing went fine:
to build:
west build -b nrf54l15dk...
During development we noticed that current measurements coming from npm1300 appear to be much higher than expected despite the results not matching what we were seeing on...
Hello, I have a question about the headphone jack output on the nRF5340 Audio DK.
In past DevZone threads, it has been stated that “the headphone output through the CS47L63...
Hello,
With reference to BLE Fundamentals Lesson 4, I am try to modify my existing BLE code to add indication support.
After adding the codes, I can see the "Read and...
We are encountering an issue with flashing firmware to our newly designed nRF54L05 BLE board.
Issue Details:
We are trying to flash a .hex file (simple Blinky code...
Dear Nordic Support,
I am currently performing initial tests for distance measurement using Channel Sounding with the nRF54L15 Development Kit.
Here are the details of...
We have previously used nRF52840 and for the latest iteration of our board design we are updating to use nRF54L15.
We are aware that for nRF52840 we could map any pin to...
