void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi Nordic people,
According to my knowledge SPI can not verify the bits whether it is properly sending or not(like ack),speed wise is SPI ok,And in nordic nRF52840 have...
Hi!
I'm trying to use the LIS2DH12 driver on SDK 16.0.0 in SES. I've managed to read the correct value of who am i register. I'm trying to configure the sensor using LIS2DH12_DATA_CFG...
I have set up 2 nrf52 dev kits: one central and one peripheral. The peripheral side hits the PM_EVT_CONN_SEC_FAILED event about 30 seconds after the connection was established...
I'm trying every permutation.
Pressing IF BOOT/RESET button along with BUTTON 4 and powering off and on the board ... then letting the buttons go
There is a reset...
Hello,
it would seem that the Spi Slave example provided with the SDK 12.3.0 does not work correctly for the nRF51DK. Setup:
Master SPI : STM30G070CB Slave SPI : nF51DK...
Good day,
I have a problem with a custom board I have designed. It does not advertise the BLE device when programmed. I am testing with the simple ble_blinky and the nrf_connect...
I have nrf52840 development boards, when I ran DFU example (from NRF SDK for thread and zigbee v4.0.0) on autocommissioning true on 2 boards and was able to run it successfully...
Hi,
Is there any way to disconnect the NRF Toolbox connection through code. I tried to do the same but once ble turns back on its connecting back to NRF toolbox.
Hello,
I'm using (nRF 52840)Laird BL654 Module. I want to test PA/LNA Features Without a Soft device. please Suggest me how to test.
Regard's
-Nikunj Patel
Hello, I come from China, there is a new thingy:91 board,I had set bluetooth gateways,added sim card,added a device nrf-352656100749665 , update certificates and the modem...
Hi
I'm using NRF53840 dongle as master the connect to my controller, and i need to choose the beacon side NRF,
My application it's, i need to recognize the beacons the...
Hi all, I'm developing software for nRF52832.
It includes function of SAADC.
My saadc_callback function is below.
It fills buffer at that time.
However, I'm wondering...
I was wondering if anyone could vouch for the accuracy of the Thingy 52's humidity sensor? I have an inexpensive humidity sensor already, and it is around 15-20% lower than...
Hi everybody,
I am testing Phy Coded with nRF52840 and Android.
But I see that the nRF Connect on Android phone (MI9) scans only 1 second with an interval of 10 seconds...
