Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hello ! I encountered a problem in sending and receiving data from one nrf51 card to another nrf52 card
i use this method in (ble_config.c) to send string data :
void...
Using the nrfx_qspi driver, it is possible to put a QSPI memory into DPM to save power, this all works fine and well. We want to keep the memory in DPM when uninitiating the...
Hi all,
I make a key using nrf52832. It tranfer data to other device. I have 2 option for this. Using beacon (BLE) or Enhanced ShockBurst (ESB) . I want to optimize energy...
Hi,
I was wondering what are the main differences between the different libraries included in the SDK that are meant to be implementations of ring buffers. I'm talking specifically...
Hi
I am developing a product for the health care market, and we chose embOS by Segger to by our OS for the nRF52840 Based product.
I've created a project based on ble_app_uart...
I am trying to send some data from RPi , And I am using the example of NRf Uart APP.
printf("\r\nUART example started.\r\n");
while (true) { uint8_t cr; // printf(" \r...
Hello All.
I try to build a generic function that read device reg over its I2C. I take the TWI master example of Nordic.
There is need for callback function to get in...
Hi
We are using your product nRF51x22_QFN48 with a balun BALF-NRF01E3 from ST and the PA.11 antenna from Taoglas Ltd.
Do you already have this product certified for RED...
Hi guys,
We have noticed some unexpected behavior of supervision timeout in case of few fast sequential calls of connect and disconnect commands in nRF connect app with...
hi...
i am using nrf52382 segger 15.2 version , i am facing issues i couldn't able to send the data ,here i am advertising using condition if my condition satisfied start...
Hello,
I use SDK15.2, SES4.12 and custom board with nRF52840.
I have a strip of ws2812b LED's connected to my device. I've made a simple RGB animation, each frame of which...
Hi,
I've been testing the sample code at_clent with Verizon wireless. I can send AT command to the DK via nRF Connect "LTE Link Monitor".
Q1. run AT%XCBAND=? to print...
Hi ,
I found nRF24LU1+ build in AES co-processor, but I cannot found the processing speed (the time for finish one AES processing) on datasheet.
Because my customer...
