Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Hi All,
I am trying to run the uart example that comes with NRF51822 development kit. I've set up the mother board (nrf6310) according to the sdk doc and have flash the...
Dear Nordic Developer Zone,
I am using nRF51822 with softdevice.
I don't understand very well the advertising mode "whitelist".
My target is to be able to connect...
Hi all!
I'm running my code based on example "ble_app_template". When advertising without doing anything else, the current comsuption is about 200 uA.
Then I added a...
Hi,
i just started again working with nrf51822 but now with eclipse+gcc and with new soft device S130.
I am struggling with the addresses of flash and ram. I want to...
I have been working on porting my code from Keil to gcc because it has grown larger than the 32K limit that the free version of Keil allows. I am using the s110 softdevice...
Hello, I have a problem during first programing PCA10003 blinky_example. I get an error:"Flash Download failed - "Cortex-M0" "
Keil v4.74
SDK v6.0.0
In nRFgo Studio...
I've been trying to get the SDK softdevice ble demos to work on a mbed board. I'm using pyOCD+linux. I can compile and flash elf (.out) files in gdb with 'load' and I can...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
The nRF51822-EK, when powered over USB, seems to be working on 3.0V. The C232HM SPI cable is a 3.3V cable. The nRF51 data sheet specifies VIO as VDD+0.3 as absolute maximum...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hi - I saw this post and I'm not sure how to add a clarifying question on to it:
devzone.nordicsemi.com/.../
We have a similar problem in that we built our boards with...
Hello,
I am working on an application that involves sampling audio data ~8KHz. I have a few questions
The real time clock module has a maximum interrupt frequency...
Hi everyone,
I bought two NRF24L01+ off ebay a couple of week ago and started to work on them this week. I seem to have problem with establishing a reliable communication...
Hi,
I use : An nRF51822 mbed kit + Kiel 5
So I updated the firmware like this : mbed.org/.../ and I dropped s110_nRF51822_v6.000 into MBED(H:)
I successfully use...
Hi,
i read about a new Chip revision of nrf51822. So i have to buy new Development Kit. How can i find out what it is the actual DK and where to buy it. I don't want to...