I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
Hello,
once synchronized, what is the minimum time for exchanging acknowledged packet.
according to datasheet :
Timeslot periods
The Gazell Link Layer supports...
I've setup Eclipse GCC tools for building and debugging as per the nAN-29 app note (and lot of online help) and able to build the code. However, the debugging is working only...
I'm new in nordic.
I want to use nRF51822 as an iBeacon for iOS.
This is possible?
There is an example, documentation for this ?
I have nRF51822 BLUTOOTH SMART BEACON...
I'm interested in working off the reference design for the nrf51822 to create my own board. I have a few questions about the 3 inductors specified on the schematic/BOM:
...
hi,
I an trying to enable notification from server. According to spec. i have to write 0x01 to the CCCD handle in heart rate characteristic in ble_app_hrs. In the BLE_GATTS_EVT_WRITE...
hi everyone
(1) everytime,the pstorage_init get the same block id, if we wrtie it more than 20,000 times , will this block become a bad one? if it will, can the program automatically...
Hi, Ole
I am using Nordic development board with Nordic dongle to communicate,..but I am getting receive link loss. I have removed reset from error handler, though the...
I have a setup where I will be switching the nRF51822 UART between two different peripherals (one being a connection to another nRF51822), so I need to be able to safely close...
Folks,
Sorry if I'm just being boneheaded here, but have been fighting with a couple problems while migrating my app on nRF51822/"C0"/SDK 4.2.2/S110 5 to nRF51822/"G0"...
We have made a custom board using nRF51822 connected to a MPU6050 accelerometer running on a battery.
Currently, we have issues performing reset on the chip. We have to...
Hi
I'm trying to measure the frequency of a pulse signal that runs at a moderate pace, varying between 50 and 500Hz while the SoftDevice is active. The softdevice needs...
Hi all,
I am having a bit of a problem with the printf. I could not figure out what could be the problem. From what I search people seem to be getting it working with out...
hi....
how can i implement bonding in app_ble_hrs example code from SDK V6.1.0 with soft device V7.0.0. the bonding should be done with a pass key.
can any one help...
Tried V5 a few months ago. But Nordic Semi didn't support their devices at that time.
I installed V5 today, and found a bunch of goodies :-), even including a nRF-RTX!
...
Hi
We did a few tests with the S120 softdevice (example in the SDK 5.1). Most things are working as expected, but the range of the device is by far less than we reached with...
