Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hi all,
I'm really new with nrf zephyr environement, so for now I've build a custom board build with nrf9161 (look similar to circuit dojo feather nrf9160). I'm able to...
We would like to change BLE's PHY setting 2Mbps to 1Mbps in Audio profile. In SDK ver2.3.0, we could find BLE's PHY setting as follows;
Let me confirm the point to be modified...
Hi there:
I want to do BLE FOTA on nRF5340 Audio DK board. I have sdk v2.6.2. I'm trying to make the existing audio application work by taking the source code as it is from...
So I am using the NRF5340, and it has been fine for a few months now, however today, it stopped working and sending any data between the USB and laptop, the LED5 flashes once...
Hello!
Any and all guidance on the issue described below would be greatly appreciated! I am happy to provide any additional information.
Thank you for your time, ...
Hello Nordic,
As described regarding BLE Serialization in the link https://nordic-prod.zoominsoftware.io/bundle/sdk_nrf5_v12.3.0/page/lib_serialization.html, we want to...
Hello,
I have developed a custom board for the nrf52840 with the QFAA QFN48 package.
I am trying to program it with my nRF52840, I am using P20 of the DKconnecting the...
I am wondering if someone can help point me to a repo that explains how to create a gpio interrupt that can detect when my CS line goes from High to Low and jump to a method...
I'm evaluating an OpenThread mesh network in a large warehouse and considering the nRF21540 Front-End Module (FEM) for the router devices. To test this setup, I purchased...
Hi,I have been trying to configure two I2S devices where I will read data from mic SPH0645 with NRF5340 then I need to send that data to Amplifier(TAS2563).So,help me configuring...
Hi, I have a question regarding the operating voltage range of the nRF5340. I found that it can operate between 1.7 and 5.5 volts. However, can we restrict the minimum voltage...
Hello,
I am developing a BLE keyboard. I am using SDK17.1.0 and nRF52840. The part that is stuck is multi-pairing. I need to develop a function that alternately connects...
Hi Team, I am currently working with the nRF52833 BLE module, and I’ve noticed that the BLE device takes approximately 16 seconds to reconnect after a disconnection from the...
Hello,
I bought a NRF52840 USB Dongle for evaluation purpose (bigger project in mind).
I cannot even run the demo from NRF Connect (like BLE or RSSI viewer)!
On my...
