I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
Hi,
We are using nRF52820 right now and we would like to decrease the current of advertising, I have set the "init.config.ble_adv_slow_interval" to ''1024'' and the average...
ref. an earlier ticket,
I am using ncs 2.0.0 on a custom nRF52840 board
When enabling the CAF BLE state module, I get a build assert error due to
BUILD_ASSERT(!IS_ENABLED...
OpenThread daemon fails to run whenever using the nRF 52840 DK development board but works fine when using the nRF 52840 Dongle. I reinstalled it multiple times and started...
I would like to test he Wi-Fi Provisioning Service sample ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/wifi/provisioning/sample_description.html...
Hi guys,
for a current project, we need access to the local Zigbee binding table of the device (getting information about the binding of the current device).
I've spend...
Hi Nordic,
When I was using NRF52840 for FCC certification, the DTM 8dBm, 2Mbps sideband emission power exceeded the standard.
The antenna matching circuit is to use the...
Hello All,
I am using nrf9160 based custom board with external flash. I am trying to build an application with mcuboot, primary image in internal flash and secondary image...
I am developing with nrf52832 (s132 v7.0.1, SDK v17.0.0) as a peripheral device.
I am communicating with an Android device (SH-M05) as central.
There are times when I...
Hello,
We are developing a device that uses only NUS (Nordic UART Service) and DFU from the services. In this case, is it possible to implement Pair/Bonded with a client...
Hi,
I am currently trying to get the USB CDC ACM Example on the nRF52 DK to work using the SDK v14.1.0 . But for some reason I can only send/receive data using PuTTY but...
I found this post devzone.nordicsemi.com/.../zephyr-central-to-peripheral-communication , which was helpful to understand the overall structure of both central_uart and central_hr...
I'm trying to build the UART app with SES as per this example:
And I'm getting this error in SES:
Did I miss a step in the installation and setup somewhere?
Dear Support team
1) I find that there is a C9 in the nRF52840 reference circuitry for CKAA WLCSP which said that the C9 is not required for Fxx and later as the picture...
Hi,
I am using ppk2 to measure current on a custom board based on particle bsom (nrf52840). I am running ampere meter mode and I can measure some current, but values looks...
Hello Nordic Community,
I installed the serial LTE modem application on my Thingy:91 so that I may use it as a standalone modem. Using minicom on my Linux machine, whenever...
