Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
In ESB, what is the function of esb_config. selective_auto_ack? What is the relationship between esb_config. selective_auto_ack and esb_payload.noack ?
Hello,
I'm using the Fanstel BC832 module which contains Nordic's nRF52832 BLE chip on a custom PCB board. When trying to run the Blinky example on PlatformIO, it works...
Hello,
we are debugging the asset_tracker_v2 on nRF9160 DK in VS Code with the nRF Debug backend, but unfortunately the global and static variables are not shown in the...
Hello,
Can the SAADC driver be modified to be used in a polling mode instead of interrupt?
E.g. I modify the driver to not use any interrupt(comment out interrupt enabling...
Our project uses nrf5340, and we hope to match it with two wm8904 audio chips. They communicate with each other using the I2S protocol. However, we noticed that two I2S buses...
Greetings,
I am trying to pair nRF52840 DK to second admin (controller) using the provided chip-tool and the switch app from the nrf samples.
Specs:
nRF52840 DK (DUT...
Hi, So I I'm working with nRF52833_xxAA on a custom board. I want to be able to debug without erasing all after power reset so I followed this tutorial.
And I was following...
We would like to try using the standard DFU process to update third party device connected to the nrf52 chip.
For proof-of-concept I want to use DFU update with experimental...
The toolchain manager always fails with the following error: Failed to clone the repositories: env: bash: No such file or directory
MacOS Big Sur
nRF Connect for Desktop...
This is more of a zephyr question I suppose, but is there anywhere I can look at a list of setting key values pairs? Or alternatively what is the best way for getting the...
Hi
For nRF52840 as Zigbee Coordinator, for an unknown new device (ED), after the new device joins the Zigbee network,
Is it possible to know the Profile, End-Point,...
Hello, guys!
We have FCC/CE/UKCA/RCM/EAC certified board that contains nRF51822 SoC. We currently don't have a possibility to enable the internal DC/DC regulator of nRF51822...
Hi,
I am moving from FreeRTOS to Zephyr. So I jused some of your simple example for trying to understand basics. I edited it little bit.
I have some default task from...
Hello,
I'm using the flash MX25L1283 together with the NRF52840. I've implemented a new driver for that flash using the nrfx library. Everything works fine !
However,...
