Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I have implemented bonding mechanism in nRF52832 firmware. But when I use nRF Connect to connect nRF52832 device sencond time. nRF Connect still request entering passkey again...
Hello
We have a product where the central can connect almost every slave. It works fine, but when connecting client slave it connects fine and finds service fine but always...
I am not using any wireless radio in my application with nRF52840 . What is the best practice to terminate ANT(H23) pin.Shall I connect it to the ground/pull up or leave it...
Board: nRF52810
SoftDevice: s112
SDK version: 17.0.2
I've developed a BLE application where nRF52810 as peripheral and nRF52833 as central. The peripheral continuously...
Hi everyone,
I am developing android app. This app can control nRF5 devices. This is a kind of smart home project. I have 5 nRF in my house and these nRF devices control...
I wanted to make a timer interrupt I went through the devzone support and saw the following post
I have 2 questions
Question one
I am following the Zephyr API. I...
Hi support team,
I have searched the forum , the infocenter and the specification, but didn't find the relevant info about how a LPN node initates the iv update if a LPN...
I have custom nRF5340 code that includes application and bootloader for both cores. For reliability reasons, I need to run bluetooth behaviour from both the netcore application...
hi ,
I'm testing this example sdk17.1\examples\peripheral\usbd_audio\pca10056\blank\arm5_no_packs.
I tested the microphone and the headphone separately.
For microphone...
The last time nRF9160 GPS API was mentioned in v1.2.0 ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.2.1/nrf/reference/kconfig/CONFIG_NRF9160_GPS.html) as was working...
I have implemented bonding mechanism in nRF52832 firmware. But when I request nRF Connect to connect nRF52832 second time. nRF52832 pm_conn_secure() return 0x3002 and nRF...
I'm trying to make a demo with nRF52840DK. And I want to power it using the coin cell. So I want to check the voltage (percentage) so that I can know how long can the device...
When I use Windows nRF Connect to connect nRF52832 device. It pop up window for user to enter passkey. But When I use iOS nRF Connect to connect nRF52832 device. It doesn...
I am trying to implement spi in my project and have encountered an issue where the delay from chipselect to sclk is around 10 us which should be as low as 1us according to...
I have been developing my code on NRF52840 based on nrfsdk v1.7. Since keil free version has a limit of 32kb i am moving my code to VS code. VS by default adds 2.0 latest...
