Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello everyone!
I am trying to figure out how SPI drivers for Bosch bme280 sensor work... I would like to somehow recycle them to write my own SPI drivers for another device...
Hi Nordic,
Using nrf-connect 1.9.99 and Zephyr 2.7.99 (*** Booting Zephyr OS build v2.7.99-ncs1-1 ***)
I am using then nRF9160-DK and everything is fine. Getting 40uA...
I'm running Manjaro Linux and have ran through the installation instructions for the nRF Connect Desktop. I have separately downloaded the Segger JLink software as instructed...
Hi Team, In my project i am using nrf52833 and i have established a network using Open Thread protocol to communicate . I am able to pair my device with the network. One scenario...
Hello, I am using 52832. There is an external interrupt count with a maximum frequency of 1kHz. I have two hardware. One I transmit to the mobile phone at an interval of 50ms...
Hello sir ,
i am trying to build file from given sample code file name is "azure_iot_hub" , i don't make any changes in this file .
on adding build configuration it show...
I have an issue from few days with the nrfCloud.
I am not able to see the live data from my devices.
However historical data is available up to the last sending so the...
I can't quite seem to figure this one out.
We've got the APP_ERROR_CHECK macro on our functions that return NRF errors. When there is a genuine error, the system does not...
Hello, I am trying to communicate with a Bosch BMI 270 device( datasheet ) using the nrf5340dk. I originally tried to use I2C since there was an example file available for...
I have an issue when registering the SIM card on nRF cloud. The save button on the form shown below won't active and can't be clicked. I have tried to fill just the asterisked...
Can anyone comment on, or point me to specific documentation, regarding creating custom control points under nRF51? I'm using both nRF51822 and nRF51922 parts. I have read...
I have a semi-working app which executes Zigbee commands that it receives from other nodes, but the latency is sometimes unacceptably high. I would like to check some of the...
Hello All,
I want to use the io function of freertos, but there is no routine for nrf52833 to use this function in the community and Google, so I want to ask whether the...
I used mergehex.exe to generate a merge.hex with firmware appcore.hex and firmware netcore.hex.
and use nrfjprog.exe flash merge.hex to nrf5340.
Prompt error:
How...
Hi,
I want to simply get RSSI at each scan in the connection less example (direction_finding_connectionless_rx). I have running two nRF52833-DK. One is flashed with RX and...
