Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hello everyone,
I created my first own layout design and the antenna. Before I order the PCB I hope you guys can review it one time. I tried to get the most informations...
Hi all.
As per subject, I'm unable to follow device using PCA10040.
Everything was set according the latest documentation available ( infocenter.nordicsemi.com/.../nRF_Sniffer_BLE_UG_v4...
To the kind attention of Nordic support team,
we are planning to use nRF5_SDK_17.1.0_ddde560 and nRF52820 for a project. We are interested in using gzp gzll library compiled...
Hello
I'm working on a project inspired by the ble_thread_dyn_mtd_coap_cli example and for which I added the management of BLE LE Secure Connections (inspired by https:...
Hi all,
I observed an issue after upgrading to 1.8.0 and to Zephyr 2.7.0-ncs1 respectively. When having Zigbee (and NET core) enabled, all images are built as before. The...
Hello there,
I've set up 1.RaspberryPi with an otbr docker container.
Thanks to Sigurd I have set up 2.nRF21540DK running CoProcessor firmware built with nRF Connect SDK...
Hi,
I want to know more about composition data size. As I have read in Mesh Profile v1.0.1, composition data page 0 is mandatory, while the other pages are optional. The...
I have custom board defined in DTS file. There will be multiple variants of boards, therefore I need to check which board is selected. How to check which board is selected...
Hi,
We are using nrf52840 for custom design and we have replaced the mx25r6435f qspi flash with Cypress S25hS512 qspi flash. We configured the flash as below in the dts...
Hello,
We have nRF52832 devices in the field, and one of the leading causes of warranty returns is that flash of nRF52 is completely erased. nrfjprog --readcode and --readuicr...
Hello,
We have a problem that affects a few devices (< 0.1 %) in mass production. The devices are flashed, boot up and pass tests and get shipped to customers. Some customers...
1. all files were successfully attached
2. there is no syntax error, there are only warnings
3. Please help me to resolve this problems as soon as possible.
Good day everyone !
Can thingy 52 itself be used as a location tracker, from Received Signal Strength Indicator(RSSI) . Does it have this function ? If it does, may i...
Hi all,
First of all, this is a new field for me, so I'm quite a beginner here. I'm connecting my ESP32 to wifi and I want to send somehow the IP it connects to, to the...
Hello,
In my application (SDK, 16.0.0, nRF 52840) I need to enable the DFU service after initialization, which I do by exposing a custom service "DFU enable". This in turn...
