Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
We are thinking of making changes to the QIAA aQFN73 circuit configuration from 5 to 4 and use the REG0 DC/DC. VDDH will be connected to a single-cell Li-Ion battery (3~4...
hi, i am working with nrf52840 and need a stand alone qspi peripheral in the project. what is the straight forward way to get qspi into the code up and running without involving...
Håkon Alseth was helping me with this: https://devzone.nordicsemi.com/f/nordic-q-a/83126/hard-fault-using-twi_scanner-example I accidentally clicked "verify answer" when trying...
Hi,
I have the Power Profiler Kit PCA63511 used on top of the dev kit PCA10040. I am trying to measure the power consumption of my custom hardware implementing nrf52832...
Hello,
I am using nrf52840, SDK 17.0.2, softdevice s140 and also implemented OTA DFU in my application.
I want to save some data lets say admin code in flash. Once I burn...
Hello,
I'm having difficulty getting the GPIO set up in a way that behaves predictably on the nRF9160 DK. As far as I understand it, the nRF52840 is what controls the GPIO...
Hi All! My question is that while using coded PHY is it possible to enable the ACK? In case no ACK receives then retransmission of the same packet to the receiver. Thanks...
I am trying to measure the frequency of the square wave on the ARDUINO_6_PIN on the NRF52840 Dev Kit. It seems like it works well until the square wave goes above 2MHz. Is...
Hi,
I see that in the latest SDK 17.1.0 there seems to be no example for regular UART but only for LPUART.
That made me wonder if there is any advantage in any scenario...
I have an external flash
S25FL132K
I am able to read , write and erase the flash with nrfx_qspi_cinstr_xfer function for 9 bytes. But I want to write more than 9 bytes...
Hi all, I am working on an electronic lock using the nRF52840. Currently it works using Bluetooth Low Energy and the lock opens when a digital key has been sent. (it has measures...
Hello sir,
I am sending the data of 252 bytes through send_notification() at each interval of time but when i send through send_notification() then following error occurs...
Hi,
I am compiling micropython port for Thingy:52. I am following instructions here https://github.com/micropython/micropython/blob/master/ports/nrf/README.md
I see that...
Hi,
I have created an HSL model and it's working fine. Now, I am using a light that has both CCT and RGB control. So, I have both HSL and CTL model existing in the same...
Board ：52840dk_52840
SDK： NCS1.7.1
IDE ：Visual Studio Code
I remap my bootloader partition in my application .overlay file
as
& boot_partition {
reg = < 0x000000000...
