I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi.
We've created a custom board, and it works nicely.
However, when I try to build another application for this new board (i.e. "Add Build Configuration"), the new board...
Hi,
I'm using the nRF Connect app on android to DFU my devices.
On some occasions, after doing DFU and unbonding, the phone will keep asking if I want to pair the device...
The Absolute Maximum rating of I/O pin voltage for VI/O, VDD ≤3.6 V is -0.3V to VDD + 0.3V in Table 185. We would like to monitor the battery voltage using an AIN pin because...
Hi, We are using the SDK v17.1.0 and SD S140 v7.2.0. In our application we have to send only 1 advertising packet with updated data every 300ms and in some cases every 50ms...
Hi,
I work with win10 laptop, Toolchain nrf Connect SDK 1.6.1 on a nrf5340dk.
I modifyed peripheral_uart to use 240 bytes like it's explain into "ncs 1.6.1 peripheral_uart...
Hi, I am trying to create a custom BLE service.
Following is the main code:
These are my BLE write functions:
My sdk_config file says MAX_MTU is defined 23
...
Hello everyone,
I have a few questions related to NFC in nrf52832.
1. UUID in nrf52832 NFC is Unique?
2. Can I use nrf52832 NFC for payment purposes..? if yes How I...
Hello sir,
I am using nrf52832 soc with customised board want to use as UART pins as RX pins as 23 and TX pins as 24 .Is it possible to use the RX pins as 23 and Tx pins...
Hello,
I am trying to configure a Zigbee coordinator as done in the CLI example (for example 'bdb role zc' and 'bdb start') to get data from the multi sensor example,...
Hello,
Lately we've had some problems with DFU using the NRF connect app.
The device we are using is a nrf52832 running Zephyr 2.6 with MCUBoot 1.8
When we set the following...
Hi,
Turning on A-GPS (using the SUPL library) causes our application to encounter a boot panic ("unable to find bootable image"). Similarly, running the nRF9160 GPS example...
Hi Dev team,
I have been working with the MQTT example and building up my application. I establish a successful connection with the broker and everything runs fine for 5...
I had trouble connecting the device to the computer. My computer shows that it is connected, however, in VS code, it cannot find the device. Also, when I tried to use the...
