Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
When running in High Voltage mode, it specifies a maximum of 7mA of external power draw on the Vdd output. It also specifies the voltage accuracy of -10%/+5%. This is a very...
HI devzone
Everytime after i executed "nrfjprog -f nrf53 --recover" on nrf5340 DK
i see it write around 4KB data into the flash. do you know what is the meaning for this...
When writing to flash it is MUCH easier to perform the write if SoftDevice is disabled. If it is not, one has to wait for an event to continue writing. ON the Nordic platforms...
Hi,
Is it possible to set the USB serial number for the nrf52833 and nrf52820 MCU's?
For the nrf52840 I've found this documentation: https://infocenter.nordicsemi.com...
I want to try Zephyr on the nrf52dk_nrf52832. (PCA10040)
I can not get it to work.
If I try to use -DBOARD=nrf52dk_nrf52810 All is OK
Here is what I do:
cd ~/zephyr_test...
Hi There,
I have several nRF52840 DK/Dongle boards, I try to run BLE Mesh applications on them. If I want to save the logs on the boards into the flash memories, what should...
Hi,
I wonder if there is a way to boot the old OTA Image even if the new one got verified? Lets say I realise in production environment there is still an issue and I want...
Hi
Yes. I want to do something like Peripheral_uart example but I want to connect my serial device sensor to NRF5340-DK via gpio pins available.
Then I want to get the...
Hi
I am trying to include DPPI within the zephyr/sample/basic/blinky example, but im so much confused on these DPPI setups, please help me to understand better.
i have...
Hi,
In your nRF9160 Product Specification rev. 2.0, you have changed the recommended decoupling of DEC0, VDD1 and VDD2 (ref chapter 10.3 Reference circuitry).
For DEC0...
Hey, I'm new to this so I will need some help. I have custom board with 453-00059 ( BL653μ with nRF52833 ) and first I want just chip to be seen on my bluetooth devices list...
Hi there,
We are trying to download and install the nRF Connect SDK v1.5.1, which seems to be the latest version on Toolchain Manager.
However, after installation, the...
I'm using the Azure Iot hub example a base for a new project I'm working on.
I've copied the example into its own folder, and can run it and connect my Azure IoT hub.
...
Hi Nordic team,
My dev environment is as follows:
nrf52840 + s140 +SD6.0.0 + SDK15.0.0 + SES + nrf52840-DK
nrf52840 is configured as BLE central with bonding enabled...
