Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Dear Members,
I tried to compile :
E:\nRF5_SDK_17.0.2_d674dde\examples\ant\ant_broadcast\tx\main.c
I got this error :
..\..\..\..\..\..\..\components\libraries\util...
Dear Members,
I want to port a code from :
E:\nRF5_SDK_17.0.2_d674dde\examples\ant\ant_async_transmitter\main.c
to be used with PCA10056 ?
Any ideas ? thanks
Hi,
I have following questions
1. How to define the limit for number of bonding information stored in internal ROM of nrf52832?
2. We want to verify the bonding functionality...
Hi Sir
We have a project with nRF5340,
Coz our product will be a smart watch, we will need to re-programming our product after full assemble in production line,
So,...
Hi all
We observed a strange behaviour with mcuboot / bootutil in our nrf9160 based project.
The bootloader log messages showed that something with the primary image is...
I run the ./nrf/samples/bluetooth/peripheral_uart example on 52840DK and connect to it using the nRF Toolbox UART section.
The connection works and I can send messages to...
Hello,
I want to modify the lte_ble_gateway app (nRF connect SDK 1.6.0) to connect with the nRF52DK advertising through the ble_app_uart (nRF 17.0.2) application. The lte_ble_gateway...
Hello,
I am trying to test 1 central 4 peripheral multilink(with saadc).
However, when the master-slave(central-peripheral) is connected,
the connection disconnected...
As the title states, my program (and a simple idle/hello world program for that matter) pull approximately 600-800 uA at idle. Same exact program, driver, and config on my...
Hi all, I am trying to write a driver for a TMP116 temp sensor based off the existing Zephyr TMP116 driver. I have added in functionality to enable the interrupt pin to enable...
1. I am tried to clear DTLS session during lwm2m session using coap_security_destroy() . I have added logging and I can see ntf_tls_free() is called from coap_security_destroy...
I'm using DWM1001-DEV, which has UWB and nrf BLE features, and my ultimate goal is replicating Apple's Airtag with DWM1001-DEV. For this, I have to ensure the power consumption...
Hello. Our company develops an electronic device, that includes using of Bluetooth Low Energy technology. We do not familiar yet with the benefits of being a Member of Bluetooth...
